0.96” – Sinocrystal https://sinocrystal.net Fri, 25 Feb 2022 08:44:25 +0000 en-US hourly 1 https://wordpress.org/?v=5.3.15 https://sinocrystal.net/wp-content/uploads/2020/06/logo_small-100x100.png 0.96” – Sinocrystal https://sinocrystal.net 32 32 0.96'' Vertical 64×128 OLED Display With SH1107 IC, 13PIN, 4wire Serial Interface, I2C https://sinocrystal.net/product/0-96-vertical-64x128-oled-display-with-sh1107-ic-13pin-4wire-serial-interface-i2c Thu, 13 Aug 2020 07:06:50 +0000 https://www.sinocrystal.net/?post_type=product&p=1560 SCE096013-V01 is a Vertical OLED Display with COG Type, 64x128 Resolution, SH1107 IC, 4wire serial interface, I2C, 13PIN

The post 0.96'' Vertical 64x128 OLED Display With SH1107 IC, 13PIN, 4wire Serial Interface, I2C first appeared on Sinocrystal.

]]>                           Drawing

 

 

 

 

                         General Specification

 

ITEM SPECIFICATIONS  UNIT
  MODULE SIZE 24.74(W)x16.9(H)x1.42(D) mm
  VIEWING AREA 22.74 (W) x 11.86(H) mm
  ACTIVE AREA 21.74 (W) x10.86(H) mm
  DOT SIZE 0.15(W) x0.15(H) mm
  DOT PITCH 0.17(W) x0.17 (H) mm
  ASSY.TYPE COG —
  WEIGHT TBD

 

 

 

 

 

                         Interface Definition

 

PIN NO. SYMBOL TYPE FUNCTION DESCRIPTIONS
1 NC(GND) P It should be connected to external ground.
2 C2P C1P/C1N-Pin for charge pump capacitor.
C2P/C2N-Pin for charge pump capacitor.
Connect to each other with a capacitor. They must be floated when the
Charge pump not use.
3 C2N
4 C1P I
5 C1N
6 VBAT P Power supply for charge pump regulator circuit.
It must be connected to external source when charge pump is used. It must be float when charge pump is not used.
7 NC NC
8 VSS P Ground pin. It must be connected to external ground.
9 VDD P Power pin for logic circuit. It must be connected to external source.
10 BS0 I Interface selection pins.

 

BS0 BS1
I2C 0 1
3-wire SPI 1 0
4-wire SPI 0 0
11 BS1
12 NC NC.
13 CS# I Chip Select input pin. Active “L”
14 RES# I Hardware reset input pin. Active “L”.
15 D/C# I This is Data/Command control pin.
When the pin is pulled HIGH, the data at D[7:0]  is data. When the pin is pulled LOW, the data at D[7:0] is command. In I2C mode, this pin acts as SA0 for slave address section.
When 3-wire serial interface is selected, this pin must be connected to VSS
16 NC NC.
17 NC NC.
18 D0 I/O When serial interface mode is selected,D2 should be either tied LOW or tied together with D1 as the serial data input: SDIN, and D0 will be the serial clock input: SCLK.
When I2C mode is selected, D2, D1 should be tied together and serve as SDA and D0
is the serial clock input, SCL.
19 D1
20 D2
22 NC NC.
23 NC NC.
24 NC NC.
25 NC NC.
26 IREF I Current reference for brightness adjustment.
This is segment output current reference pin. A resistor should be connected between this pin and VSS .Set the current at 12.5 uA maximum.
27 VCOMH O COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS.
28 VCC P Power supply for OLED driving voltage. A capacitor should be connected between this pin and VSS, when charge pump is used.
It must be connected to external source when charge pump is not used.
29 VLSS P This is an analog ground pin. It should be connected to VSS externally.
30 NC(GND) P It should be connected to external ground.

The post 0.96'' Vertical 64x128 OLED Display With SH1107 IC, 13PIN, 4wire Serial Interface, I2C first appeared on Sinocrystal.

]]> 0.96” 128×64 OLED With SSD1315Z IC, 30PIN, 3/4wire Serial Interface, I2C https://sinocrystal.net/product/0-96-128x64-oled-with-ssd1315z-ic-30pin-3-4wire-serial-interface-i2c Thu, 13 Aug 2020 06:59:35 +0000 https://www.sinocrystal.net/?post_type=product&p=1557 SCE096009-V01 is a OLED Display with COG Type, 128×64 Resolution, SSD1315Z IC, 3/4wire serial interface, I2C, 30PIN

The post 0.96'' 128×64 OLED With SSD1315Z IC, 30PIN, 3/4wire Serial Interface, I2C first appeared on Sinocrystal.

]]>                           Drawing

 

 

 

 

                         General Specification

 

ITEM SPECIFICATIONS  UNIT
  MODULE SIZE 24.74(W)x16.9(H)x1.42(D) mm
  VIEWING AREA 22.74 (W) x 11.86(H) mm
  ACTIVE AREA 21.74 (W) x10.86(H) mm
  DOT SIZE 0.15(W) x0.15(H) mm
  DOT PITCH 0.17(W) x0.17 (H) mm
  ASSY.TYPE COG —
  WEIGHT TBD

 

 

 

 

 

                         Interface Definition

 

PIN NO. SYMBOL TYPE FUNCTION DESCRIPTIONS
1 NC(GND) P It should be connected to external ground.
2 C2P C1P/C1N-Pin for charge pump capacitor.
C2P/C2N-Pin for charge pump capacitor.
Connect to each other with a capacitor. They must be floated when the
Charge pump not use.
3 C2N
4 C1P I
5 C1N
6 VBAT P Power supply for charge pump regulator circuit.
It must be connected to external source when charge pump is used. It must be float when charge pump is not used.
7 NC NC
8 VSS P Ground pin. It must be connected to external ground.
9 VDD P Power pin for logic circuit. It must be connected to external source.
10 BS0 I Interface selection pins.

BS0 BS1
I2C 0 1
3-wire SPI 1 0
4-wire SPI 0 0
11 BS1
12 NC NC.
13 CS# I Chip Select input pin. Active “L”
14 RES# I Hardware reset input pin. Active “L”.
15 D/C# I This is Data/Command control pin.
When the pin is pulled HIGH, the data at D[7:0]  is data. When the pin is pulled LOW, the data at D[7:0] is command. In I2C mode, this pin acts as SA0 for slave address section.
When 3-wire serial interface is selected, this pin must be connected to VSS
16 NC NC.
17 NC NC.
18 D0 I/O When serial interface mode is selected,D2 should be either tied LOW or tied together with D1 as the serial data input: SDIN, and D0 will be the serial clock input: SCLK.
When I2C mode is selected, D2, D1 should be tied together and serve as SDA and D0
is the serial clock input, SCL.
19 D1
20 D2
22 NC NC.
23 NC NC.
24 NC NC.
25 NC NC.
26 IREF I Current reference for brightness adjustment.
This is segment output current reference pin. A resistor should be connected between this pin and VSS .Set the current at 12.5 uA maximum.
27 VCOMH O COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS.
28 VCC P Power supply for OLED driving voltage. A capacitor should be connected between this pin and VSS, when charge pump is used.
It must be connected to external source when charge pump is not used.
29 VLSS P This is an analog ground pin. It should be connected to VSS externally.
30 NC(GND) P It should be connected to external ground.

The post 0.96'' 128×64 OLED With SSD1315Z IC, 30PIN, 3/4wire Serial Interface, I2C first appeared on Sinocrystal.

]]> 0.96” 128×64 OLED With SSD1316 IC, 15PIN, 4 SPI Interface https://sinocrystal.net/product/0-96-128x64-oled-with-ssd1316-ic-15pin-4-spi-interface Thu, 13 Aug 2020 06:55:26 +0000 https://www.sinocrystal.net/?post_type=product&p=1554 SCE096006-V01 is a OLED Display with COG Type, 128×64 Resolution, SSD1306 IC, 4 SPI interface, 15PIN

The post 0.96'' 128×64 OLED With SSD1316 IC, 15PIN, 4 SPI Interface first appeared on Sinocrystal.

]]>  

 

                         General Specification

 

 

ITEM SPECIFICATIONS  UNIT
  MODULE SIZE 26.7(W)x19.26(H)x1.227(D) mm
  VIEWING AREA 23.74 (W) x 13.2(H) mm
  ACTIVE AREA 21.74(W) x11.2 (H) mm
  DOT SIZE 0.15(W) x0.15(H) mm
  DOT PITCH 0.17(W) x0.17 (H) mm
  ASSY.TYPE COG —
  WEIGHT TBD

 

 

 

 

 

                         Interface Definition

 

 

PIN NO. SYMBOL TYPE FUNCTION DESCRIPTIONS
1 NC(GND) P It should be connected to external ground.
2 C2P C1P/C1N-Pin for charge pump capacitor.
C2P/C2N-Pin for charge pump capacitor.
Connect to each other with a capacitor. They must be floated when the
Charge pump not use.
3 C2N
4 C1P I
5 C1N
6 VBAT P Power supply for charge pump regulator circuit.
It must be connected to external source when charge pump is used. It must be float when charge pump is not used.
7 NC NC
8 VSS P Ground pin. It must be connected to external ground.
9 VDD P Power pin for logic circuit. It must be connected to external source.
10 BS0 I Interface selection pins.

I2C 6800 8080 4SPI
BS0 0 0 0 0
BS1 1 0 1 0
BS2 0 1 1 0
11 BS1
12 BS2
13 CS# I Chip Select input pin. Active “L”
14 RES# I Hardware reset input pin. Active “L”.
15 D/C# I This is Data/Command control pin.
When the pin is pulled HIGH, the data at D[7:0]  is data. When the pin is pulled LOW, the data at D[7:0] is command. In I2C mode, this pin acts as SA0 for slave address section.
When 3-wire serial interface is selected, this pin must be connected to VSS
16 R/W# I This is read/write control input pin.
8080: data write enable; 6800: read/write select pin.
When serial or I2C interface is selected, this pin must be connected to VSS.
17 E# I This is read/write control input pin.
8080: data read enable; 6800: read/write enable pin.
When serial or I2C interface is selected, this pin must be connected to VSS.
18 D0 I/O These are 8-bit bi-directional data bus to be connected to microprocessor’s Data bus.
When serial interface mode is selected, D2 should be kept NC, D1 will be the serial data input: SDIN, D0 will be the serial clock input: SCLK.
When I2C mode is selected, D2, D1 should be tied together and serve as SDA and D0 is the serial clock input, SCL.
19 D1
20 D2
21 D3
22 D4
23 D5
24 D6
25 D7
26 IREF I Current reference for brightness adjustment.
This is segment output current reference pin. A resistor should be connected between this pin and VSS .Set the current at 12.5 uA maximum.
27 VCOMH O COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS.
28 VCC P Power supply for OLED driving voltage. A capacitor should be connected between this pin and VSS, when charge pump is used.
It must be connected to external source when charge pump is not used.
29 VLSS P This is an analog ground pin. It should be connected to VSS externally.
30 NC(GND) P It should be connected to external ground.

The post 0.96'' 128×64 OLED With SSD1316 IC, 15PIN, 4 SPI Interface first appeared on Sinocrystal.

]]> 0.96” 128×64 OLED With SSD1316BZ IC,30PIN 6800/8080 Interface, 4 Wire Serial I2C https://sinocrystal.net/product/0-96-128x64-oled-with-ssd1316bz-ic30pin-6800-8080-interface-4-wire-serial-i2c Thu, 13 Aug 2020 06:53:27 +0000 https://www.sinocrystal.net/?post_type=product&p=1553 SCE096004-V01 is a OLED Display with COG Type, 128×64 Resolution, SSD1306BZ IC, 4 wire serial interface, 30PIN

The post 0.96'' 128×64 OLED With SSD1316BZ IC,30PIN 6800/8080 Interface, 4 Wire Serial I2C first appeared on Sinocrystal.

]]>                           Drawing

 

 

 

 

                         General Specification

 

ITEM SPECIFICATIONS  UNIT
  MODULE SIZE 26.7(W)x19.26(H)x1.227(D) mm
  VIEWING AREA 23.74 (W) x 13.2(H) mm
  ACTIVE AREA 21.74(W) x11.2 (H) mm
  DOT SIZE 0.15(W) x0.15(H) mm
  DOT PITCH 0.17(W) x0.17 (H) mm
  ASSY.TYPE COG —
  WEIGHT TBD

 

 

 

                         Interface Definition

 

PIN NO. SYMBOL TYPE FUNCTION DESCRIPTIONS
1 NC(GND) P It should be connected to external ground.
2 C2P C1P/C1N-Pin for charge pump capacitor.
C2P/C2N-Pin for charge pump capacitor.
Connect to each other with a capacitor. They must be floated when the
Charge pump not use.
3 C2N
4 C1P I
5 C1N
6 VBAT P Power supply for charge pump regulator circuit.
It must be connected to external source when charge pump is used. It must be float when charge pump is not used.
7 NC NC
8 VSS P Ground pin. It must be connected to external ground.
9 VDD P Power pin for logic circuit. It must be connected to external source.
10 BS0 I Interface selection pins.

I2C 6800 8080 4SPI
BS0 0 0 0 0
BS1 1 0 1 0
BS2 0 1 1 0
11 BS1
12 BS2
13 CS# I Chip Select input pin. Active “L”
14 RES# I Hardware reset input pin. Active “L”.
15 D/C# I This is Data/Command control pin.
When the pin is pulled HIGH, the data at D[7:0]  is data. When the pin is pulled LOW, the data at D[7:0] is command. In I2C mode, this pin acts as SA0 for slave address section.
When 3-wire serial interface is selected, this pin must be connected to VSS
16 R/W# I This is read/write control input pin.
8080: data write enable; 6800: read/write select pin.
When serial or I2C interface is selected, this pin must be connected to VSS.
17 E# I This is read/write control input pin.
8080: data read enable; 6800: read/write enable pin.
When serial or I2C interface is selected, this pin must be connected to VSS.
18 D0 I/O These are 8-bit bi-directional data bus to be connected to microprocessor’s Data bus.
When serial interface mode is selected, D2 should be kept NC, D1 will be the serial data input: SDIN, D0 will be the serial clock input: SCLK.
When I2C mode is selected, D2, D1 should be tied together and serve as SDA and D0 is the serial clock input, SCL.
19 D1
20 D2
21 D3
22 D4
23 D5
24 D6
25 D7
26 IREF I Current reference for brightness adjustment.
This is segment output current reference pin. A resistor should be connected between this pin and VSS .Set the current at 12.5 uA maximum.
27 VCOMH O COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS.
28 VCC P Power supply for OLED driving voltage. A capacitor should be connected between this pin and VSS, when charge pump is used.
It must be connected to external source when charge pump is not used.
29 VLSS P This is an analog ground pin. It should be connected to VSS externally.
30 NC(GND) P It should be connected to external ground.

The post 0.96'' 128×64 OLED With SSD1316BZ IC,30PIN 6800/8080 Interface, 4 Wire Serial I2C first appeared on Sinocrystal.

]]> 0.96 Inch Mono OLED With 128×64, SSD1316BZ IC,30PIN, 6800/8080 Interface, 4 Wire Serial Interface, I2C https://sinocrystal.net/product/0-96-inch-mono-oled-with-128x64-ssd1316bz-ic30pin-6800-8080-interface-4-wire-serial-interface-i2c Thu, 13 Aug 2020 06:49:23 +0000 https://www.sinocrystal.net/?post_type=product&p=1549 SCE096003-V01 is a OLED Display with COG Type, 128×64 Resolution, SSD1306BZ IC, 4 wire serial interface, 30PIN

The post 0.96 Inch Mono OLED With 128×64, SSD1316BZ IC,30PIN, 6800/8080 Interface, 4 Wire Serial Interface, I2C first appeared on Sinocrystal.

]]>                           Drawing

 

 

 

                         General Specification

 

ITEM SPECIFICATIONS  UNIT
  MODULE SIZE 26.7(W)x19.26(H)x1.227(D) mm
  VIEWING AREA 23.74 (W) x 13.2(H) mm
  ACTIVE AREA 21.74(W) x11.2 (H) mm
  DOT SIZE 0.15(W) x0.15(H) mm
  DOT PITCH 0.17(W) x0.17 (H) mm
  ASSY.TYPE COG —
  WEIGHT TBD

 

 

 

                         Interface Definition

 

PIN NO. SYMBOL TYPE FUNCTION DESCRIPTIONS
1 NC(GND) P It should be connected to external ground.
2 C2P C1P/C1N-Pin for charge pump capacitor.
C2P/C2N-Pin for charge pump capacitor.
Connect to each other with a capacitor. They must be floated when the
Charge pump not use.
3 C2N
4 C1P I
5 C1N
6 VBAT P Power supply for charge pump regulator circuit.
It must be connected to external source when charge pump is used. It must be float when charge pump is not used.
7 NC NC
8 VSS P Ground pin. It must be connected to external ground.
9 VDD P Power pin for logic circuit. It must be connected to external source.
10 BS0 I Interface selection pins.

I2C 6800 8080 4SPI
BS0 0 0 0 0
BS1 1 0 1 0
BS2 0 1 1 0
11 BS1
12 BS2
13 CS# I Chip Select input pin. Active “L”
14 RES# I Hardware reset input pin. Active “L”.
15 D/C# I This is Data/Command control pin.
When the pin is pulled HIGH, the data at D[7:0]  is data. When the pin is pulled LOW, the data at D[7:0] is command. In I2C mode, this pin acts as SA0 for slave address section.
When 3-wire serial interface is selected, this pin must be connected to VSS
16 R/W# I This is read/write control input pin.
8080: data write enable; 6800: read/write select pin.
When serial or I2C interface is selected, this pin must be connected to VSS.
17 E# I This is read/write control input pin.
8080: data read enable; 6800: read/write enable pin.
When serial or I2C interface is selected, this pin must be connected to VSS.
18 D0 I/O These are 8-bit bi-directional data bus to be connected to microprocessor’s Data bus.
When serial interface mode is selected, D2 should be kept NC, D1 will be the serial data input: SDIN, D0 will be the serial clock input: SCLK.
When I2C mode is selected, D2, D1 should be tied together and serve as SDA and D0 is the serial clock input, SCL.
19 D1
20 D2
21 D3
22 D4
23 D5
24 D6
25 D7
26 IREF I Current reference for brightness adjustment.
This is segment output current reference pin. A resistor should be connected between this pin and VSS .Set the current at 12.5 uA maximum.
27 VCOMH O COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS.
28 VCC P Power supply for OLED driving voltage. A capacitor should be connected between this pin and VSS, when charge pump is used.
It must be connected to external source when charge pump is not used.
29 VLSS P This is an analog ground pin. It should be connected to VSS externally.
30 NC(GND) P It should be connected to external ground.

The post 0.96 Inch Mono OLED With 128×64, SSD1316BZ IC,30PIN, 6800/8080 Interface, 4 Wire Serial Interface, I2C first appeared on Sinocrystal.

]]> 0.96” OLED Display With 128×64 Resolution SSD1316BZ IC,30PIN, 6800/8080 Interface, 4 Wire Serial Interface, I2C https://sinocrystal.net/product/0-96-oled-display-with-128x64-resolution-ssd1316bz-ic30pin-6800-8080-interface-4-wire-serial-interface-i2c Thu, 13 Aug 2020 06:42:47 +0000 https://www.sinocrystal.net/?post_type=product&p=1545 SCE091003-V01 is a OLED Display with COG Type, 128×32 Resolution, SSD1306BZ IC, 4 wire serial interface, 15PIN

The post 0.96'' OLED Display With 128×64 Resolution SSD1316BZ IC,30PIN, 6800/8080 Interface, 4 Wire Serial Interface, I2C first appeared on Sinocrystal.

]]>                           Drawing

 

 

 

                         General Specification

 

ITEM SPECIFICATIONS  UNIT
  MODULE SIZE 26.7(W)x19.26(H)x1.227(D) mm
  VIEWING AREA 23.74 (W) x 13.2(H) mm
  ACTIVE AREA 21.74(W) x11.2 (H) mm
  DOT SIZE 0.15(W) x0.15(H) mm
  DOT PITCH 0.17(W) x0.17 (H) mm
  ASSY.TYPE COG —
  WEIGHT TBD

 

 

 

                         Interface Definition

 

PIN NO. SYMBOL TYPE FUNCTION DESCRIPTIONS
1 NC(GND) P It should be connected to external ground.
2 C2P C1P/C1N-Pin for charge pump capacitor.
C2P/C2N-Pin for charge pump capacitor.
Connect to each other with a capacitor. They must be floated when the
Charge pump not use.
3 C2N
4 C1P I
5 C1N
6 VBAT P Power supply for charge pump regulator circuit.
It must be connected to external source when charge pump is used. It must be float when charge pump is not used.
7 NC NC
8 VSS P Ground pin. It must be connected to external ground.
9 VDD P Power pin for logic circuit. It must be connected to external source.
10 BS0 I Interface selection pins.
11 BS1
12 BS2
13 CS# I Chip Select input pin. Active “L”
14 RES# I Hardware reset input pin. Active “L”.
15 D/C# I This is Data/Command control pin.
When the pin is pulled HIGH, the data at D[7:0]  is data. When the pin is pulled LOW, the data at D[7:0] is command. In I2C mode, this pin acts as SA0 for slave address section.
When 3-wire serial interface is selected, this pin must be connected to VSS
16 R/W# I This is read/write control input pin.
8080: data write enable; 6800: read/write select pin.
When serial or I2C interface is selected, this pin must be connected to VSS.
17 E# I This is read/write control input pin.
8080: data read enable; 6800: read/write enable pin.
When serial or I2C interface is selected, this pin must be connected to VSS.
18 D0 I/O These are 8-bit bi-directional data bus to be connected to microprocessor’s Data bus.
When serial interface mode is selected, D2 should be kept NC, D1 will be the serial data input: SDIN, D0 will be the serial clock input: SCLK.
When I2C mode is selected, D2, D1 should be tied together and serve as SDA and D0 is the serial clock input, SCL.
19 D1
20 D2
21 D3
22 D4
23 D5
24 D6
25 D7
26 IREF I Current reference for brightness adjustment.
This is segment output current reference pin. A resistor should be connected between this pin and VSS .Set the current at 12.5 uA maximum.
27 VCOMH O COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS.
28 VCC P Power supply for OLED driving voltage. A capacitor should be connected between this pin and VSS, when charge pump is used.
It must be connected to external source when charge pump is not used.
29 VLSS P This is an analog ground pin. It should be connected to VSS externally.
30 NC(GND) P It should be connected to external ground.

The post 0.96'' OLED Display With 128×64 Resolution SSD1316BZ IC,30PIN, 6800/8080 Interface, 4 Wire Serial Interface, I2C first appeared on Sinocrystal.

]]> 0.96” IPS TFT Normal Black Transmissive LCD Display With 80*160 Resolution ST7735S https://sinocrystal.net/product/0-96-ips-tft-normal-black-transmissive-lcd-display-with-80160-resolution-st7735s Mon, 10 Aug 2020 09:52:25 +0000 https://www.sinocrystal.net/?post_type=product&p=1306 SCT009003-V01 is a 0.96" mini TFT LCD display, with 80*160 resolution. This module is built in with ST7735S IC. It is a portrait mode LCD module.

The post 0.96'' IPS TFT Normal Black Transmissive LCD Display With 80*160 Resolution ST7735S first appeared on Sinocrystal.

]]>  

                         SCT009003-V01 a 0.96-inch small size IPS active matrix Normal Black TFT LCD Display with transmissive mode.

                         This display with size: 27.95 x 13.54 x 1.85 mm; active area 21.7 x 10.8 mm (0.96 inch).

                         Resolution of this model is 80×160 pixels (width 80 pixels x height 160 pixels) and every pixel is made up of three vertical strips of Red, Green and Blue dots.

                         It’s a IPS Display with wide viewing angle which is one of the most popular techniques on the market now.

                         This mini size 0.96” TFT LCD display module has built-in ST7735S IC and SPI interface.

                         The brightness of this display is 300 cd/m2 with contrast ratio 800:1.

                         LCM voltage ranges from 3V-3.6V, typical value is 3.3V. Operating temperature covers from -20~+70℃, storage temperature range is from -30~+80℃.

 

 

 

                         Drawing

 

 

 

 

 

 

                         General Specification

 

Item Nominal Dimension Unit
 Dot Matrix 80 x RGB x 160 Dots
 Module Size ( W×H×T ) 13.54 x 27.95 x 1.5 mm.
 Active Area ( W×H ) 10.80 x 21.70 mm.
 Pixel arrangement RGB Stripe mm.
 Dot Pitch ( W×H ) 0.135 x 0.1356 mm.
 Color depth 262K(MAX) colors
 Interface SPI –
 Driving IC ST7735S –
 Operating temperature -20 ~70 ºC
 Storage temperature -30~80 ºC
 LCD Type a-Si TFT –
 LCD Mode Normal Black –
 Backlight Type LED x 1 PCS

 

 

 

 

                         Interface Definition

 

Pin No Pin Symbol Type Description
1 LED+ P LED light, anode
2 LED- P LED light, cathode.
3 D/C I In 4-line SPI:
-D/CX=’1′: Display Data or Parameter.
-D/CX=’0′: Command Data.
In 3-line SPI: no used
If not used, please fix this pin at GND level
4 SDA I/O Serial data input/output signal
5 CS I Chip Select
6 RESET I Chip reset signal
7 SCL I Serial clock input signal
–   SPI4W=’0′, 3-line SPI Enable.
8 SPI4W I –   SPI4W=’1′, 4-line SPI Enable.
9 VCC P Power supply
10 GND P Ground

The post 0.96'' IPS TFT Normal Black Transmissive LCD Display With 80*160 Resolution ST7735S first appeared on Sinocrystal.

]]> 0.96'' Round IPS Color LCD Screen With 240*198 Resolution GC9307, 1 Lane 4SPI /8080 Mode interface https://sinocrystal.net/product/0-96-round-ips-color-lcd-screen-with-240198-resolution-gc9307-interface-1-lane-4spi-8080-mode Mon, 10 Aug 2020 02:48:33 +0000 https://www.sinocrystal.net/?post_type=product&p=1302 SCT009004-V01 is a TFT Display with COG Type, 240(RGB)*198 Resolution, GC9307 IC, 1 Lane 4SPI /8080 mode interface,  IPS  Transmissive  Normal Black, 24PIN with all viewing angle.

The post 0.96'' Round IPS Color LCD Screen With 240*198 Resolution GC9307, 1 Lane 4SPI /8080 Mode interface first appeared on Sinocrystal.

]]>  

                         Drawing

 

 

 

                         General Specification

 

 

Item Nominal Dimension Unit
 Dot Matrix 240 x RGB x 198 Dots
 Module Size ( W×H×T ) 27.40(W) X 27.00(H) X 1.46(T) mm.
 Active Area ( W×H ) 24.408(H) X 20.137(V) mm.
 Pixel arrangement RGB Stripe mm.
 Dot Pitch ( W×H ) 0.135 x 0.1356 mm.
 Color depth 262K(MAX) colors
 Interface 1 Lane 4SPI /8080 mode –
 Driving IC GC9307 –
 Operating temperature -10 ~60 ºC
 Storage temperature -20~70 ºC
 LCD Type a-Si TFT –
 LCD Mode IPS/ Transmissive / Normal Black –
 Backlight Type LED x 1 PCS

 

 

                         Interface Definition

 

 

Pin No. Symbol I/O Description
1 VSS P GND
2 IM1\IM2 I IM1/IM2=0,8080 8bit mode

 

IM1/IM2=1,4SPI 1lane mode
3 RES I Hardware Reset input pin
4 NC – Open
5 CS I Chip select input pins
6 DCX/SCL I SPI mode: Serial clock input

 

8080 mode: data and command select pin
7 NC – open
8 VDDIO P Power source for I/O circuit
9 VDD P Power source for system circuit
10 NC – open
11 LEDK P Backlight –
12 LEDA P Backlight +
13 TE O Tearing effect signal is used to synchronize MCU to frame memory
14 D7  

 

 

 

 

 

 

I\O

  

 

 

 

 

 

Parallel interface data bus
15 D6
16 D5
17 D4
18 D3
19 D2
20 D1
21 D0
22 SDA I Serial data input
23 RD I Read enable in 8080 mode
24 WR/A0 I 8080 mode: write enable

SPI mode: data and command select pin

 

The post 0.96'' Round IPS Color LCD Screen With 240*198 Resolution GC9307, 1 Lane 4SPI /8080 Mode interface first appeared on Sinocrystal.

]]>