0,66-дюймовый OLED-дисплей с разрешением 64 × 48 SSD1306BZ IC, 30PIN
SCE066001-V03 — это OLED-дисплей с типом COG, разрешением 64 × 48, SSD1306BZ IC, интерфейсом 6800/8080, 4-проводным последовательным интерфейсом I2C, 30PIN
Описание
рисунок
Основные Характеристики
| ITEM | SPECIFICATIONS | UNIT |
| MODULE SIZE | 18.46(W)x18.1(H)x1.21(D) | mm |
| VIEWING AREA | 15.42 (W) x 12.06(H) | mm |
| ACTIVE AREA | 13.42 (W) x10.06(H) | mm |
| DOT SIZE | 0.19(W) x0.19(H) | mm |
| DOT PITCH | 0.21(W) x0.21 (H) | mm |
| ASSY.TYPE | COG | — |
| WEIGHT | TBD |
Определение интерфейса
| PIN NO. | SYMBOL | TYPE | FUNCTION DESCRIPTIONS |
| 1 | NC | NC. | |
| 2 | C2P | C1P/C1N-Pin for charge pump capacitor. C2P/C2N-Pin for charge pump capacitor. Connect to each other with a capacitor. They must be floated when the Charge pump not use. |
|
| 3 | C2N | ||
| 4 | C1P | I | |
| 5 | C1N | ||
| 6 | VBAT | P | Power supply for charge pump regulator circuit. It must be connected to external source when charge pump is used. It must be float when charge pump is not used. |
| 7 | NC | NC. | |
| 8 | VSS | P | Ground pin. It must be connected to external ground. |
| 9 | VDD | P | Power pin for logic circuit. It must be connected to external source. |
| 10 | NC | NC. | |
| 11 | BS1 | I | Bitmap Interface selection pins. |
| 12 | BS2 | ||
| 13 | CS# | I | Chip Select input pin. Active «L» |
| 14 | RES# | I | Hardware reset input pin. Active «L». |
| 15 | D/C# | I | This is Data/Command control pin. When the pin is pulled HIGH, the data at D[7:0] is data. When the pin is pulled LOW, the data at D[7:0] is command. In I2C mode, this pin acts as SA0 for slave address section. When 3-wire serial interface is selected, this pin must be connected to VSS |
| 16 | R/W# | I | This is read/write control input pin. 8080: data write enable; 6800: read/write select pin. When serial or I2C interface is selected, this pin must be connected to VSS. |
| 17 | E/RD# | I | This is read/write control input pin. 8080: data read enable; 6800: read/write enable pin. When serial or I2C interface is selected, this pin must be connected to VSS. |
| 18 | D0 | I/O | These are 8-bit bi-directional data bus to be connected to microprocessor’s Data bus. When serial interface mode is selected, D2 should be kept NC, D1 will be the serial data input: SDIN, D0 will be the serial clock input: SCLK. When I2C mode is selected, D2, D1 should be tied together and serve as SDA and D0 is the serial clock input, SCL. |
| 19 | D1 | ||
| 20 | D2 | ||
| 21 | D3 | ||
| 22 | D4 | ||
| 23 | D5 | ||
| 24 | D6 | ||
| 25 | D7 | ||
| 26 | IREF | I | Current reference for brightness adjustment. This is segment output current reference pin. A resistor should be connected between this pin and VSS .Set the current at 12.5 uA maximum. |
| 27 | VCOMH | O | COM signal deselected voltage level. A capacitor should be connected between this pin and VSS. |
| 28 | VCC | P | Power supply for OLED driving voltage. A capacitor should be connected between this pin and VSS, when charge pump is used. It must be connected to external source when charge pump is not used. |
| 29 | NC | NC. | |
| 30 | NC | NC. |
Детали
| P-Type | |
|---|---|
| mode | |
| Product No. | SCE066003-V01 |
| Size | |
| Resolution | |
| outline dimension | |
| Active Area | |
| IC | |
| Brightness | |
| Touch Screen | |
| View Direction | |
| Pin No | |
| Shape | |
| interface |
