128*64 – Sinocrystal https://sinocrystal.net Fri, 25 Feb 2022 08:44:25 +0000 en-US hourly 1 https://wordpress.org/?v=5.3.15 https://sinocrystal.net/wp-content/uploads/2020/06/logo_small-100x100.png 128*64 – Sinocrystal https://sinocrystal.net 32 32 2.7” 128×64 OLED With SPD0301ZD IC, 24PIN https://sinocrystal.net/product/2-7-128x64-oled-with-spd0301zd-ic-24pin Tue, 26 Jan 2021 01:38:09 +0000 https://sinocrystal.net/?post_type=product&p=5007 SCE270001-V01 is a OLED Display with 128×64 Resolution, SSD1325 IC, 6800/8080 interface, 4 wire serial interface, I2C, 30PIN

The post 2.7'' 128×64 OLED With SPD0301ZD IC, 24PIN first appeared on Sinocrystal.

]]>  

                         Drawing

 

 

 

 

 

                         General Specification

 

ITEM SPECIFICATIONS  UNIT
 MODULE SIZE 89.70 × 47.20 × 3.40 mm
 VIEWING AREA 73.00 × 41.86 × 2.00 mm
 ACTIVE AREA 61.41 × 30.69 mm
 DOT SIZE 0.45 × 0.45 mm
 DOT PITCH 0.48 × 0.48 mm
 Resolution 128 x 64 —
Display Color Monochrome (Yellow / 16 Gray Scales)

 

The post 2.7'' 128×64 OLED With SPD0301ZD IC, 24PIN first appeared on Sinocrystal.

]]> 1.54” 128×64 OLED With SPD0301ZD IC, 24PIN https://sinocrystal.net/product/1-54-128x64-oled-with-spd0301zd-ic-24pin-6800-8080-interface-4-wire-serial-interface-i2c Thu, 13 Aug 2020 08:12:29 +0000 https://www.sinocrystal.net/?post_type=product&p=1577 SCE154001-V01 is a OLED Display with COG Type, 128×64 Resolution, SPD0301ZD IC, 6800/8080 interface, 4 wire serial interface, I2C, 30PIN

The post 1.54'' 128×64 OLED With SPD0301ZD IC, 24PIN first appeared on Sinocrystal.

]]>  

                         Drawing

 

 

 

 

                         General Specification

 

ITEM SPECIFICATIONS  UNIT
 MODULE SIZE 42.04(W)x27.22(H)x1.41(D) mm
 VIEWING AREA 37.052 (W) x 19.516(H) mm
 ACTIVE AREA 35.052(W) x17.516(H) mm
 DOT SIZE 0.254(W) x0.254(H) mm
 DOT PITCH 0.274(W) x0.274 (H) mm
 ASSY.TYPE COG —
 WEIGHT TBD

 

 

 

 

                         Interface Definition

 

PIN NO. SYMBOL TYPE FUNCTION DESCRIPTIONS
1 NC(GND) P It should be connected to external ground.
2 VLSS P This is an analog ground pin. It should be connected to VSS externally.
3 VSS P Ground pin. It must be connected to external ground.
4 NC NC
5 VDD P Power pin for logic circuit. It must be connected to external source.
6 BS1 I

Interface selection pins.

I2C 6800 8080 4SPI
BS1 1 0 1 0
BS2 0 1 1 0
7 BS2
8 CS# I Chip Select input pin. Active “L”
9 RES# I Hardware reset input pin. Active “L”.
10 D/C# I WThis is Data/Command control pin.
When the pin is pulled HIGH, the data at D[7:0]  is data.
When the pin is pulled LOW, the data at D[7:0] is command. In I2C mode, this pin acts as SA0 for slave address section.
When 3-wire serial interface is selected, this pin must be connected to VSS
11 R/W# I This is read/write control input pin.
8080: data write enable; 6800: read/write select pin.
When serial or I2C interface is selected, this pin must be connected to VSS.
12 E/RD# I This is read/write control input pin.
8080: data read enable; 6800: read/write enable pin.
When serial or I2C interface is selected, this pin must be connected to VSS.
13 D0 I/O These are 8-bit bi-directional data bus to be connected to microprocessor’s Data bus.
When serial interface mode is selected, D2 should be kept NC, D1 will be the serial data input: SDIN, D0 will be the serial clock input: SCLK.
When I2C mode is selected, D2, D1 should be tied together and serve as SDA and D0 is the serial clock input, SCL.
14 D1
15 D2
16 D3
17 D4
18 D5
19 D6
20 D7
21 IREF I Current reference for brightness adjustment.
This is segment output current reference pin. A resistor should be connected between this pin and VSS .Set the current at 10 uA maximum.
22 VCOMH O COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS.
23 VCC P Power supply for OLED driving voltage. A capacitor should be connected between this pin and VSS.
24 NC(GND) P It should be connected to external ground.

The post 1.54'' 128×64 OLED With SPD0301ZD IC, 24PIN first appeared on Sinocrystal.

]]> 1.3” 128×64 OLED With SH1106G IC, 30PIN https://sinocrystal.net/product/1-3-128x64-oled-with-sh1106g-ic-30pin-6800-8080-interface-4-wire-serial-interface-i2c Thu, 13 Aug 2020 07:10:51 +0000 https://www.sinocrystal.net/?post_type=product&p=1563 SCE0130001-V01 is a OLED Display with COG Type, 128×64 Resolution, SH1106G IC, 6800/8080 interface, 4 wire serial interface, I2C, 30PIN

The post 1.3'' 128×64 OLED With SH1106G IC, 30PIN first appeared on Sinocrystal.

]]>  

                         Drawing

 

1.3'' OLED Display

 

 

                         General Specification

 

ITEM SPECIFICATIONS  UNIT
 MODULE SIZE 34.5(W)x23.0(H)x1.427(D) mm
 VIEWING AREA 31.42 (W) x 16.7(H) mm
 ACTIVE AREA 29.42(W) x14.7(H) mm
 DOT SIZE 0.21(W) x0.21(H) mm
 DOT PITCH 0.23(W) x0.23 (H) mm
 ASSY.TYPE COG —
 WEIGHT TBD

 

 

 

 

 

                         Interface Definition

 

PIN NO. SYMBOL TYPE FUNCTION DESCRIPTIONS
1 NC(GND) P It should be connected to external ground.
2 C2P I C1P/C1N-Pin for charge pump capacitor.
C2P/C2N-Pin for charge pump capacitor.
Connect to each other with a capacitor. They must be floated when the
Charge pump not use.
3 C2N
4 C1P
5 C1N
6 VBAT P Power supply for charge pump regulator circuit.
It must be connected to external source when charge pump is used. It must be float when charge pump is not used.
7 VSS P Ground pin. It must be connected to external ground.
8 VSS
9 VDD P Power pin for logic circuit. It must be connected to external source.
10 BS0 I Interface selection pins.

 

I2C 6800 8080 4SPI
BS0 0 0 0 0
BS1 1 0 1 0
BS2 0 1 1 0
11 BS1
12 BS2
13 CS# I Chip Select input pin. Active “L”
14 RES# I Hardware reset input pin. Active “L”.
15 D/C# I This is Data/Command control pin.
When the pin is pulled HIGH, the data at D[7:0]  is data. When the pin is pulled LOW, the data at D[7:0] is command. In I2C mode, this pin acts as SA0 for slave address section.
When 3-wire serial interface is selected, this pin must be connected to VSS
16 R/W# I This is read/write control input pin.
8080: data write enable; 6800: read/write select pin.
When serial or I2C interface is selected, this pin must be connected to VSS.
17 E# I This is read/write control input pin.
8080: data read enable; 6800: read/write enable pin.
When serial or I2C interface is selected, this pin must be connected to VSS.
18 D0 I/O These are 8-bit bi-directional data bus to be connected to microprocessor’s Data bus.
When serial interface mode is selected, D2 should be kept NC, D1 will be the serial data input: SDIN, D0 will be the serial clock input: SCLK.
When I2C mode is selected, D2, D1 should be tied together and serve as SDA and D0 is the serial clock input, SCL.
19 D1
20 D2
21 D3
22 D4
23 D5
24 D6
25 D7
26 IREF O Current reference for brightness adjustment.
This is segment output current reference pin. A resistor should be connected between this pin and VSS .Set the current at 12.5 uA maximum.
27 VCOMH O COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS.
28 VCC P Power supply for OLED driving voltage. A capacitor should be connected between this pin and VSS, when charge pump is used.
It must be connected to external source when charge pump is not used.
29 NC This is an analog ground pin. It should be connected to VSS externally.
30 NC(GND) P It should be connected to external ground.

 

The post 1.3'' 128×64 OLED With SH1106G IC, 30PIN first appeared on Sinocrystal.

]]> 0.96” 128×64 OLED With SSD1315Z IC, 30PIN, 3/4wire Serial Interface, I2C https://sinocrystal.net/product/0-96-128x64-oled-with-ssd1315z-ic-30pin-3-4wire-serial-interface-i2c Thu, 13 Aug 2020 06:59:35 +0000 https://www.sinocrystal.net/?post_type=product&p=1557 SCE096009-V01 is a OLED Display with COG Type, 128×64 Resolution, SSD1315Z IC, 3/4wire serial interface, I2C, 30PIN

The post 0.96'' 128×64 OLED With SSD1315Z IC, 30PIN, 3/4wire Serial Interface, I2C first appeared on Sinocrystal.

]]>                           Drawing

 

 

 

 

                         General Specification

 

ITEM SPECIFICATIONS  UNIT
  MODULE SIZE 24.74(W)x16.9(H)x1.42(D) mm
  VIEWING AREA 22.74 (W) x 11.86(H) mm
  ACTIVE AREA 21.74 (W) x10.86(H) mm
  DOT SIZE 0.15(W) x0.15(H) mm
  DOT PITCH 0.17(W) x0.17 (H) mm
  ASSY.TYPE COG —
  WEIGHT TBD

 

 

 

 

 

                         Interface Definition

 

PIN NO. SYMBOL TYPE FUNCTION DESCRIPTIONS
1 NC(GND) P It should be connected to external ground.
2 C2P C1P/C1N-Pin for charge pump capacitor.
C2P/C2N-Pin for charge pump capacitor.
Connect to each other with a capacitor. They must be floated when the
Charge pump not use.
3 C2N
4 C1P I
5 C1N
6 VBAT P Power supply for charge pump regulator circuit.
It must be connected to external source when charge pump is used. It must be float when charge pump is not used.
7 NC NC
8 VSS P Ground pin. It must be connected to external ground.
9 VDD P Power pin for logic circuit. It must be connected to external source.
10 BS0 I Interface selection pins.

BS0 BS1
I2C 0 1
3-wire SPI 1 0
4-wire SPI 0 0
11 BS1
12 NC NC.
13 CS# I Chip Select input pin. Active “L”
14 RES# I Hardware reset input pin. Active “L”.
15 D/C# I This is Data/Command control pin.
When the pin is pulled HIGH, the data at D[7:0]  is data. When the pin is pulled LOW, the data at D[7:0] is command. In I2C mode, this pin acts as SA0 for slave address section.
When 3-wire serial interface is selected, this pin must be connected to VSS
16 NC NC.
17 NC NC.
18 D0 I/O When serial interface mode is selected,D2 should be either tied LOW or tied together with D1 as the serial data input: SDIN, and D0 will be the serial clock input: SCLK.
When I2C mode is selected, D2, D1 should be tied together and serve as SDA and D0
is the serial clock input, SCL.
19 D1
20 D2
22 NC NC.
23 NC NC.
24 NC NC.
25 NC NC.
26 IREF I Current reference for brightness adjustment.
This is segment output current reference pin. A resistor should be connected between this pin and VSS .Set the current at 12.5 uA maximum.
27 VCOMH O COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS.
28 VCC P Power supply for OLED driving voltage. A capacitor should be connected between this pin and VSS, when charge pump is used.
It must be connected to external source when charge pump is not used.
29 VLSS P This is an analog ground pin. It should be connected to VSS externally.
30 NC(GND) P It should be connected to external ground.

The post 0.96'' 128×64 OLED With SSD1315Z IC, 30PIN, 3/4wire Serial Interface, I2C first appeared on Sinocrystal.

]]> 0.96” 128×64 OLED With SSD1316 IC, 15PIN, 4 SPI Interface https://sinocrystal.net/product/0-96-128x64-oled-with-ssd1316-ic-15pin-4-spi-interface Thu, 13 Aug 2020 06:55:26 +0000 https://www.sinocrystal.net/?post_type=product&p=1554 SCE096006-V01 is a OLED Display with COG Type, 128×64 Resolution, SSD1306 IC, 4 SPI interface, 15PIN

The post 0.96'' 128×64 OLED With SSD1316 IC, 15PIN, 4 SPI Interface first appeared on Sinocrystal.

]]>  

 

                         General Specification

 

 

ITEM SPECIFICATIONS  UNIT
  MODULE SIZE 26.7(W)x19.26(H)x1.227(D) mm
  VIEWING AREA 23.74 (W) x 13.2(H) mm
  ACTIVE AREA 21.74(W) x11.2 (H) mm
  DOT SIZE 0.15(W) x0.15(H) mm
  DOT PITCH 0.17(W) x0.17 (H) mm
  ASSY.TYPE COG —
  WEIGHT TBD

 

 

 

 

 

                         Interface Definition

 

 

PIN NO. SYMBOL TYPE FUNCTION DESCRIPTIONS
1 NC(GND) P It should be connected to external ground.
2 C2P C1P/C1N-Pin for charge pump capacitor.
C2P/C2N-Pin for charge pump capacitor.
Connect to each other with a capacitor. They must be floated when the
Charge pump not use.
3 C2N
4 C1P I
5 C1N
6 VBAT P Power supply for charge pump regulator circuit.
It must be connected to external source when charge pump is used. It must be float when charge pump is not used.
7 NC NC
8 VSS P Ground pin. It must be connected to external ground.
9 VDD P Power pin for logic circuit. It must be connected to external source.
10 BS0 I Interface selection pins.

I2C 6800 8080 4SPI
BS0 0 0 0 0
BS1 1 0 1 0
BS2 0 1 1 0
11 BS1
12 BS2
13 CS# I Chip Select input pin. Active “L”
14 RES# I Hardware reset input pin. Active “L”.
15 D/C# I This is Data/Command control pin.
When the pin is pulled HIGH, the data at D[7:0]  is data. When the pin is pulled LOW, the data at D[7:0] is command. In I2C mode, this pin acts as SA0 for slave address section.
When 3-wire serial interface is selected, this pin must be connected to VSS
16 R/W# I This is read/write control input pin.
8080: data write enable; 6800: read/write select pin.
When serial or I2C interface is selected, this pin must be connected to VSS.
17 E# I This is read/write control input pin.
8080: data read enable; 6800: read/write enable pin.
When serial or I2C interface is selected, this pin must be connected to VSS.
18 D0 I/O These are 8-bit bi-directional data bus to be connected to microprocessor’s Data bus.
When serial interface mode is selected, D2 should be kept NC, D1 will be the serial data input: SDIN, D0 will be the serial clock input: SCLK.
When I2C mode is selected, D2, D1 should be tied together and serve as SDA and D0 is the serial clock input, SCL.
19 D1
20 D2
21 D3
22 D4
23 D5
24 D6
25 D7
26 IREF I Current reference for brightness adjustment.
This is segment output current reference pin. A resistor should be connected between this pin and VSS .Set the current at 12.5 uA maximum.
27 VCOMH O COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS.
28 VCC P Power supply for OLED driving voltage. A capacitor should be connected between this pin and VSS, when charge pump is used.
It must be connected to external source when charge pump is not used.
29 VLSS P This is an analog ground pin. It should be connected to VSS externally.
30 NC(GND) P It should be connected to external ground.

The post 0.96'' 128×64 OLED With SSD1316 IC, 15PIN, 4 SPI Interface first appeared on Sinocrystal.

]]> 0.96” 128×64 OLED With SSD1316BZ IC,30PIN 6800/8080 Interface, 4 Wire Serial I2C https://sinocrystal.net/product/0-96-128x64-oled-with-ssd1316bz-ic30pin-6800-8080-interface-4-wire-serial-i2c Thu, 13 Aug 2020 06:53:27 +0000 https://www.sinocrystal.net/?post_type=product&p=1553 SCE096004-V01 is a OLED Display with COG Type, 128×64 Resolution, SSD1306BZ IC, 4 wire serial interface, 30PIN

The post 0.96'' 128×64 OLED With SSD1316BZ IC,30PIN 6800/8080 Interface, 4 Wire Serial I2C first appeared on Sinocrystal.

]]>                           Drawing

 

 

 

 

                         General Specification

 

ITEM SPECIFICATIONS  UNIT
  MODULE SIZE 26.7(W)x19.26(H)x1.227(D) mm
  VIEWING AREA 23.74 (W) x 13.2(H) mm
  ACTIVE AREA 21.74(W) x11.2 (H) mm
  DOT SIZE 0.15(W) x0.15(H) mm
  DOT PITCH 0.17(W) x0.17 (H) mm
  ASSY.TYPE COG —
  WEIGHT TBD

 

 

 

                         Interface Definition

 

PIN NO. SYMBOL TYPE FUNCTION DESCRIPTIONS
1 NC(GND) P It should be connected to external ground.
2 C2P C1P/C1N-Pin for charge pump capacitor.
C2P/C2N-Pin for charge pump capacitor.
Connect to each other with a capacitor. They must be floated when the
Charge pump not use.
3 C2N
4 C1P I
5 C1N
6 VBAT P Power supply for charge pump regulator circuit.
It must be connected to external source when charge pump is used. It must be float when charge pump is not used.
7 NC NC
8 VSS P Ground pin. It must be connected to external ground.
9 VDD P Power pin for logic circuit. It must be connected to external source.
10 BS0 I Interface selection pins.

I2C 6800 8080 4SPI
BS0 0 0 0 0
BS1 1 0 1 0
BS2 0 1 1 0
11 BS1
12 BS2
13 CS# I Chip Select input pin. Active “L”
14 RES# I Hardware reset input pin. Active “L”.
15 D/C# I This is Data/Command control pin.
When the pin is pulled HIGH, the data at D[7:0]  is data. When the pin is pulled LOW, the data at D[7:0] is command. In I2C mode, this pin acts as SA0 for slave address section.
When 3-wire serial interface is selected, this pin must be connected to VSS
16 R/W# I This is read/write control input pin.
8080: data write enable; 6800: read/write select pin.
When serial or I2C interface is selected, this pin must be connected to VSS.
17 E# I This is read/write control input pin.
8080: data read enable; 6800: read/write enable pin.
When serial or I2C interface is selected, this pin must be connected to VSS.
18 D0 I/O These are 8-bit bi-directional data bus to be connected to microprocessor’s Data bus.
When serial interface mode is selected, D2 should be kept NC, D1 will be the serial data input: SDIN, D0 will be the serial clock input: SCLK.
When I2C mode is selected, D2, D1 should be tied together and serve as SDA and D0 is the serial clock input, SCL.
19 D1
20 D2
21 D3
22 D4
23 D5
24 D6
25 D7
26 IREF I Current reference for brightness adjustment.
This is segment output current reference pin. A resistor should be connected between this pin and VSS .Set the current at 12.5 uA maximum.
27 VCOMH O COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS.
28 VCC P Power supply for OLED driving voltage. A capacitor should be connected between this pin and VSS, when charge pump is used.
It must be connected to external source when charge pump is not used.
29 VLSS P This is an analog ground pin. It should be connected to VSS externally.
30 NC(GND) P It should be connected to external ground.

The post 0.96'' 128×64 OLED With SSD1316BZ IC,30PIN 6800/8080 Interface, 4 Wire Serial I2C first appeared on Sinocrystal.

]]> 0.96 Inch Mono OLED With 128×64, SSD1316BZ IC,30PIN, 6800/8080 Interface, 4 Wire Serial Interface, I2C https://sinocrystal.net/product/0-96-inch-mono-oled-with-128x64-ssd1316bz-ic30pin-6800-8080-interface-4-wire-serial-interface-i2c Thu, 13 Aug 2020 06:49:23 +0000 https://www.sinocrystal.net/?post_type=product&p=1549 SCE096003-V01 is a OLED Display with COG Type, 128×64 Resolution, SSD1306BZ IC, 4 wire serial interface, 30PIN

The post 0.96 Inch Mono OLED With 128×64, SSD1316BZ IC,30PIN, 6800/8080 Interface, 4 Wire Serial Interface, I2C first appeared on Sinocrystal.

]]>                           Drawing

 

 

 

                         General Specification

 

ITEM SPECIFICATIONS  UNIT
  MODULE SIZE 26.7(W)x19.26(H)x1.227(D) mm
  VIEWING AREA 23.74 (W) x 13.2(H) mm
  ACTIVE AREA 21.74(W) x11.2 (H) mm
  DOT SIZE 0.15(W) x0.15(H) mm
  DOT PITCH 0.17(W) x0.17 (H) mm
  ASSY.TYPE COG —
  WEIGHT TBD

 

 

 

                         Interface Definition

 

PIN NO. SYMBOL TYPE FUNCTION DESCRIPTIONS
1 NC(GND) P It should be connected to external ground.
2 C2P C1P/C1N-Pin for charge pump capacitor.
C2P/C2N-Pin for charge pump capacitor.
Connect to each other with a capacitor. They must be floated when the
Charge pump not use.
3 C2N
4 C1P I
5 C1N
6 VBAT P Power supply for charge pump regulator circuit.
It must be connected to external source when charge pump is used. It must be float when charge pump is not used.
7 NC NC
8 VSS P Ground pin. It must be connected to external ground.
9 VDD P Power pin for logic circuit. It must be connected to external source.
10 BS0 I Interface selection pins.

I2C 6800 8080 4SPI
BS0 0 0 0 0
BS1 1 0 1 0
BS2 0 1 1 0
11 BS1
12 BS2
13 CS# I Chip Select input pin. Active “L”
14 RES# I Hardware reset input pin. Active “L”.
15 D/C# I This is Data/Command control pin.
When the pin is pulled HIGH, the data at D[7:0]  is data. When the pin is pulled LOW, the data at D[7:0] is command. In I2C mode, this pin acts as SA0 for slave address section.
When 3-wire serial interface is selected, this pin must be connected to VSS
16 R/W# I This is read/write control input pin.
8080: data write enable; 6800: read/write select pin.
When serial or I2C interface is selected, this pin must be connected to VSS.
17 E# I This is read/write control input pin.
8080: data read enable; 6800: read/write enable pin.
When serial or I2C interface is selected, this pin must be connected to VSS.
18 D0 I/O These are 8-bit bi-directional data bus to be connected to microprocessor’s Data bus.
When serial interface mode is selected, D2 should be kept NC, D1 will be the serial data input: SDIN, D0 will be the serial clock input: SCLK.
When I2C mode is selected, D2, D1 should be tied together and serve as SDA and D0 is the serial clock input, SCL.
19 D1
20 D2
21 D3
22 D4
23 D5
24 D6
25 D7
26 IREF I Current reference for brightness adjustment.
This is segment output current reference pin. A resistor should be connected between this pin and VSS .Set the current at 12.5 uA maximum.
27 VCOMH O COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS.
28 VCC P Power supply for OLED driving voltage. A capacitor should be connected between this pin and VSS, when charge pump is used.
It must be connected to external source when charge pump is not used.
29 VLSS P This is an analog ground pin. It should be connected to VSS externally.
30 NC(GND) P It should be connected to external ground.

The post 0.96 Inch Mono OLED With 128×64, SSD1316BZ IC,30PIN, 6800/8080 Interface, 4 Wire Serial Interface, I2C first appeared on Sinocrystal.

]]> 0.96” OLED Display With 128×64 Resolution SSD1316BZ IC,30PIN, 6800/8080 Interface, 4 Wire Serial Interface, I2C https://sinocrystal.net/product/0-96-oled-display-with-128x64-resolution-ssd1316bz-ic30pin-6800-8080-interface-4-wire-serial-interface-i2c Thu, 13 Aug 2020 06:42:47 +0000 https://www.sinocrystal.net/?post_type=product&p=1545 SCE091003-V01 is a OLED Display with COG Type, 128×32 Resolution, SSD1306BZ IC, 4 wire serial interface, 15PIN

The post 0.96'' OLED Display With 128×64 Resolution SSD1316BZ IC,30PIN, 6800/8080 Interface, 4 Wire Serial Interface, I2C first appeared on Sinocrystal.

]]>                           Drawing

 

 

 

                         General Specification

 

ITEM SPECIFICATIONS  UNIT
  MODULE SIZE 26.7(W)x19.26(H)x1.227(D) mm
  VIEWING AREA 23.74 (W) x 13.2(H) mm
  ACTIVE AREA 21.74(W) x11.2 (H) mm
  DOT SIZE 0.15(W) x0.15(H) mm
  DOT PITCH 0.17(W) x0.17 (H) mm
  ASSY.TYPE COG —
  WEIGHT TBD

 

 

 

                         Interface Definition

 

PIN NO. SYMBOL TYPE FUNCTION DESCRIPTIONS
1 NC(GND) P It should be connected to external ground.
2 C2P C1P/C1N-Pin for charge pump capacitor.
C2P/C2N-Pin for charge pump capacitor.
Connect to each other with a capacitor. They must be floated when the
Charge pump not use.
3 C2N
4 C1P I
5 C1N
6 VBAT P Power supply for charge pump regulator circuit.
It must be connected to external source when charge pump is used. It must be float when charge pump is not used.
7 NC NC
8 VSS P Ground pin. It must be connected to external ground.
9 VDD P Power pin for logic circuit. It must be connected to external source.
10 BS0 I Interface selection pins.
11 BS1
12 BS2
13 CS# I Chip Select input pin. Active “L”
14 RES# I Hardware reset input pin. Active “L”.
15 D/C# I This is Data/Command control pin.
When the pin is pulled HIGH, the data at D[7:0]  is data. When the pin is pulled LOW, the data at D[7:0] is command. In I2C mode, this pin acts as SA0 for slave address section.
When 3-wire serial interface is selected, this pin must be connected to VSS
16 R/W# I This is read/write control input pin.
8080: data write enable; 6800: read/write select pin.
When serial or I2C interface is selected, this pin must be connected to VSS.
17 E# I This is read/write control input pin.
8080: data read enable; 6800: read/write enable pin.
When serial or I2C interface is selected, this pin must be connected to VSS.
18 D0 I/O These are 8-bit bi-directional data bus to be connected to microprocessor’s Data bus.
When serial interface mode is selected, D2 should be kept NC, D1 will be the serial data input: SDIN, D0 will be the serial clock input: SCLK.
When I2C mode is selected, D2, D1 should be tied together and serve as SDA and D0 is the serial clock input, SCL.
19 D1
20 D2
21 D3
22 D4
23 D5
24 D6
25 D7
26 IREF I Current reference for brightness adjustment.
This is segment output current reference pin. A resistor should be connected between this pin and VSS .Set the current at 12.5 uA maximum.
27 VCOMH O COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS.
28 VCC P Power supply for OLED driving voltage. A capacitor should be connected between this pin and VSS, when charge pump is used.
It must be connected to external source when charge pump is not used.
29 VLSS P This is an analog ground pin. It should be connected to VSS externally.
30 NC(GND) P It should be connected to external ground.

The post 0.96'' OLED Display With 128×64 Resolution SSD1316BZ IC,30PIN, 6800/8080 Interface, 4 Wire Serial Interface, I2C first appeared on Sinocrystal.

]]> 13264 Dot Matrix Graphic Display With COG STN ST7565R IC 18 PIN https://sinocrystal.net/product/13264-dot-matrix-graphic-display-with-cog-stn-st7565r-ic-18-pin Thu, 13 Aug 2020 02:01:38 +0000 https://www.sinocrystal.net/?post_type=product&p=1471 SC13264005-V30 is a 2.12inch STN COG Graphic LCD Display with Y-G Positive Transmissive, ST7565R IC, 18 PIN

The post 13264 Dot Matrix Graphic Display With COG STN ST7565R IC 18 PIN first appeared on Sinocrystal.

]]>  

                         Drawing

 

 

 

                         General Specification

 

ITEM STANDARD VALUE UNIT
NUMBER OF GRAPHIC 132×64 Mm
MODULE DIMENSION 57.5×41.7×8.1 Mm
VIEWING AREA 54.0×41.0 Mm
DOT SIZE 0.34×0.38 Mm
DOT PITCH 0.37×0.41 Mm
LCD TYPE STN/YELLOW-GREEN/POSITIVE/TRANSMISSIVE
DUTY 1/64
VIEWING DIRECTION 0.25 o’clock
BACK LIGHT TYPE SIDE LIT LED
BACK LIGHT COLOR WHITE
APPROX. WEIGHT TBD G

 

 

 

                         Interface Definition

 

NO SYMBOL LEVEL FUNCTION
1 CS1 H/L Chip select signal
2 RST H/L Chip reset signal
3 A0 H/L Register selection input
H : Indicate that D0 to D7 are display data.
L:Indicate that D0 to D7 are control data
4 D6(SCK) H/L D6 : the serial clock input (SCK)
5 D7(SDA) H/L D7 : serial data input (SDA) ;
6 VDD 3.3V Supply voltage for logic
7 VSS Ground Ground
8 VOUT — Power for LCD
9 C3+ — DC/DC voltage converter. Connect a capacitor between this
terminal and the CAP1N terminal.
10 C1- — DC/DC voltage converter. Connect a capacitor between this
terminal and the CAP1P terminal.
11 C1+ — DC/DC voltage converter. Connect a capacitor between this
terminal and the CAP1N terminal. Reset signal.
12 C2+ — DC/DC voltage converter. Connect a capacitor between this
terminal and the CAP2N terminal.
13 C2- — DC/DC voltage converter. Connect a capacitor between this
terminal and the CAP2P terminal. Chip select.
14-18 V4-V0 — This is a multi-level power supply for the liquid crystal drive.

 

 

 

 

 

                         Keywords: graphic lcd, 132×64 lcd, lcd 132×64, 132×64 dot matrix lcd display

The post 13264 Dot Matrix Graphic Display With COG STN ST7565R IC 18 PIN first appeared on Sinocrystal.

]]> Mono LCD 12864 Graphic Display With COG STN Y-G BL ST7565R IC 36 PIN https://sinocrystal.net/product/mono-lcd-12864-graphic-display-with-cog-stn-y-g-bl-st7565r-ic-36-pin Thu, 13 Aug 2020 01:52:38 +0000 https://www.sinocrystal.net/?post_type=product&p=1464 SC12864032-V02 ist ein grafisches LCD-Display mit einer Auflösung von 128 * 64, das mit dem IC ST7565R-G-1, 36 PIN und 6-Uhr-Blickrichtung ausgestattet ist.

The post Mono LCD 12864 Graphic Display With COG STN Y-G BL ST7565R IC 36 PIN first appeared on Sinocrystal.

]]>                          Drawing

 

 

 

 

 

 

                         General Specification

 

ITEM STANDARD VALUE UNIT
 NUMBER OF GRAPHIC 128×64 Mm
 MODULE DIMENSION 71.0×51.8×8.5 Mm
 VIEWING AREA 60.77×32.93 Mm
 DOT SIZE 0.45×0.49 Mm
 DOT PITCH 0.476×0.515 Mm
 LCD TYPE STN/YELLOW-GREEN/POSITIVE/TRANSMISSIVE
 DUTY 1/64
 VIEWING DIRECTION 6 o’clock
 BACK LIGHT TYPE SIDE LIT LED
 BACK LIGHT COLOR WHITE
 APPROX. WEIGHT TBD G

 

 

 

                         Interface Definition

 

NO SYMBOL LEVEL FUNCTION
1–2 NC – No used
3 CS1 H/L Chip select signal
4 RST H/L Chip reset signal
5 A0 H/L Register selection input
H : Indicate that D0 to D7 are display data.
L:Indicate that D0 to D7 are control data
6 WR(R/W) H/L 8080 series: Write signal
6800 series: Read or Write signal
7 RD(E) H/L 8080 series: Read signal
6800 series: Enable signal
8–15 This is an 8-bit bi-directional data bus that connects to an 8-bit or 16-bit standard MPU data bus.
When the serial interface (SPI-4) is selected (P/S = “L”) : D7 : serial data input (SI) ;
D6 : the serial clock input (SCL).
D0 to D5 should be connected to VDD or floating.
16 VDD — Supply voltage for logic
17 VSS — Ground
18 VOUT — Power for LCD
19 C3+ — DC/DC voltage converter. Connect a capacitor between this
terminal and the CAP1N terminal.
20 C1- — DC/DC voltage converter. Connect a capacitor between this
terminal and the CAP1P terminal.
21 C1+ — DC/DC voltage converter. Connect a capacitor between this
terminal and the CAP1N terminal. Reset signal.
22 C2+ — DC/DC voltage converter. Connect a capacitor between this
terminal and the CAP2N terminal.
23 C2- — DC/DC voltage converter. Connect a capacitor between this
terminal and the CAP2P terminal. Chip select.
24 NC – No used
25-29 V4-V0 — This is a multi-level power supply for the liquid crystal drive.
30 VR — Contrast adjustment input.
31 NC – No used
32 C86 H/L C86 = “H”: 6800 Series MPU interface.
C86 = “L”: 8080 Series MPU interface.
33 PS H/L P/S = “H”: Parallel interface
P/S = “L”: Serial interface
34 NC – No used
35 IRS H/L RS = “H”: Use the internal resistors
IRS = “L”: Do not use the internal resistors.
36 NC – No used

 

 

 

 

 

                         Keywords: 12864 lcd, lcd 128×64, 128×64, lcd 128×64 i2c, lcd 12864, 12864 cog lcd display fpc, fstn 128 64, mono lcd

The post Mono LCD 12864 Graphic Display With COG STN Y-G BL ST7565R IC 36 PIN first appeared on Sinocrystal.

]]>