30 – Sinocrystal

Small 2.2 Inch 176×220 Pixels TFT LCD Display With ILI9225G Driver IC

管理员 — Thu, 08 Jul 2021 07:55:52 +0000

Drawing

General Specification

Item	Standard value	Unit
LCD Size	2.2	inch
Dot Matrix	176(RGB) × 220	pixel
Module Size	41.90 × 55.26 × 2.35	mm
Active Area	34.85 × 43.56	mm
Dot Pitch	0.198 × 0.198	mm
Pixel Configuration	R.G.B. Stripe	–
Color depth	262K	–
Display Mode	Normally white, Transmissive	–
Technology Type	a-Si	–
Viewing Direction	6 o’clock	–
Gray Scale Inversion Direction	12 o’clock	–
Driver IC	ILI9225G	–
Interface	16-bit MCU	–
LED Numbers	3 LEDs	–
Weight	TBD	g

Interface Definition

Pin No.	Symbol	Type	Description
1	D0	I/O	Data bus
2	D1	I/O	Data bus
3	D2	I/O	Data bus
4	D3	I/O	Data bus
5	GND	P	Ground
6	IOVCC	P	Power supply for I/O
7	CS	I	Chip Select signal
8	RS	I	Display data/command selection pin in MCU interface. DCX=’1′: display data or parameter. DCX=’0′: register index / command.
9	WR	I	Write signal
10	RD	I	Read signal
11	LEDA	P	LED driving anode
12	LEDK1	P	LED driving cathode
13	LEDK2	P	LED driving cathode
14	LEDK3	P	LED driving cathode
15	D4	I/O	Data bus
16	D8	I/O	Data bus
17	D9	I/O	Data bus
18	D10	I/O	Data bus
19	D11	I/O	Data bus
20	D12	I/O	Data bus
21	D13	I/O	Data bus
22	D14	I/O	Data bus
23	D15	I/O	Data bus
24	RESET	I	Chip reset signal
25	VCI	P	Power supply for system
26	VCI	P	Power supply for system
27	GND	P	Ground
28	D5	I/O	Data bus
29	D6	I/O	Data bus
30	D7	I/O	Data bus

Focus Keyword:2.2” tft lcd display,small lcd display,176×220 lcd display, lcd display 2.2 inch screen,2.2 inch tft display

The post Small 2.2 Inch 176×220 Pixels TFT LCD Display With ILI9225G Driver IC first appeared on Sinocrystal.

2.7” 128×64 OLED With SPD0301ZD IC, 24PIN

Zhang, Renny — Tue, 26 Jan 2021 01:38:09 +0000

Drawing

General Specification

ITEM	SPECIFICATIONS	UNIT
MODULE SIZE	89.70 × 47.20 × 3.40	mm
VIEWING AREA	73.00 × 41.86 × 2.00	mm
ACTIVE AREA	61.41 × 30.69	mm
DOT SIZE	0.45 × 0.45	mm
DOT PITCH	0.48 × 0.48	mm
Resolution	128 x 64	—
Display Color	Monochrome (Yellow / 16 Gray Scales)

The post 2.7'' 128×64 OLED With SPD0301ZD IC, 24PIN first appeared on Sinocrystal.

IPS 7 inch 1024X600 HMI with converter board TFT LCD screen display

管理员 — Thu, 24 Sep 2020 07:59:48 +0000

Drawing

Mechanical Specifications

Item	Nominal Dimension	Unit
Dot Matrix	1024 x RGB x 600	Dots
Module Size ( W×H×T )	163.8 x 97.0 x 2.71	mm.
Active Area ( W×H )	154.21 x 85.92	mm.
Pixel arrangement	RGB Stripe	mm.
Dot Pitch ( W×H )	0.1506 x 0.1432	mm.
Color depth	16.7M（MAX）	colors
Interface	MIPI	–
Driving IC	EK79007 or Compatible	–

Display Specifications

Item	Nominal Dimension	Unit
Operating temperature	-20 ~70	℃
Storage temperature	-30~80	℃
LCD Type	a-Si TFT	–
LCD Mode	Normal Black	–
Backlight Type	LED x 24	PCS

Interface Definition

Pin No	Pin Symbol	Type	Description
1	LEDA	P	Backlight Power, anode.
2	LEDA	P	Backlight Power, anode.
3	VGH	P	Power supply for Gate ON Voltage
4	VGL	P	Power supply for Gate OFF Voltage
5	UPDN	I	Horizontal direction, up or down.
6	SHLR	I	Horizontal direction, left or right.
7	LEDK	P	Backlight Power, cathode.
8	LEDK	P	Backlight Power, cathode.
9	AVDD	P	Power supply analog circuit
10	GND	P	Power ground
11	D3P	I	MIPI data input
12	D3N	I	MIPI data input
13	GND	P	Power ground
14	D2P	I	MIPI data input
15	D2N	I	MIPI data input
16	GND	P	Power ground
17	CLKP	I	MIPI clock input
18	CLKN	I	MIPI clock input
19	GND	P	Power ground
20	D1P	I	MIPI data input
21	D1N	I	MIPI data input
22	GND	P	Power ground
23	D0P	I	MIPI data input
24	D0N	I	MIPI data input
25	GND	P	Power ground
26	STBYB	I	Standby mode. H: Normal operation L: Driver turn off, No output.
27	RESET	I	Reset signal
28	VDD	P	Power supply for MIPI circuit and digital circuit (1.8V)
29	VDD	P	Power supply for MIPI circuit and digital circuit (1.8V)
30	VCOM	P	Common Voltage

IPS 7 inch 1024X600 display, 7 tft lcd,lcd screen 7 inch,lcd display 7 inch,lcd 7 inch,lcd screen 7inch,7 display modules,7 inch car screen

The post IPS 7 inch 1024X600 HMI with converter board TFT LCD screen display first appeared on Sinocrystal.

1.41'' OLED With 320*360 Dot Matrix ZTW522 IC, 30PIN, MIPI Interface For Smart Watch

管理员 — Thu, 13 Aug 2020 07:16:17 +0000

Drawing

General Specification

ITEM	SPECIFICATIONS	UNIT
MODULE SIZE	26.04×31.78	mm
VIEWING AREA	26.04 x30.18	mm
ACTIVE AREA	23.84×26.82	mm
DOT SIZE	0.21(W) x0.21(H)	mm
DOT PITCH	0.23(W) x0.23 (H)	mm
ASSY.TYPE	COG	—
WEIGHT	TBD

Interface Definition

#	Pin name	I/O	Description
1	TP_INT	I/O	Interrupt to Host
2	TP_SDA	I/O	I2C Data Line
3	TP_SCL	I/O	I2C Clock Line
4	TP_VDD	Power	TP Power Supply
5	ELVDD	Power	Power supply for OLED
6	VDD1	Power	Driver IC analog supply
7	SWIRE	O	Power IC control signal
8	GND1	Power	GND
9	REST	I	This signal will reset the device and must be applied to properly initialize the chip. Active low.
10	NC	–	No connector
11	NC	–	No connector
12	NC	–	No connector
13	NC	–	No connector
14	NC	–	No connector
15	GND2	Power	GND
16	NC	–	No connector
17	GND3	Power	GND
18	DSI_D0N	I/O	MIPI DSI data0+
19	DSI_D0P	I/O	MIPI DSI data0-
20	GND4	Power	GND
21	DSI_CLKN	I/O	MIPI DSI clock-
22	DSI_CLKP	I/O	MIPI DSI clock+
23	GND5	Power	GND
24	VDDIO	Power	Driver IC digital I/O supply.
25	TE	O	Tear effect output
26	VDD2	Power	Driver IC analog supply
27	ELVSS	Power	Power supply for OLED
28	GND6	Power	GND
29	TP_RST	I	Reset
30	GND7	Power	GND

The post 1.41'' OLED With 320*360 Dot Matrix ZTW522 IC, 30PIN, MIPI Interface For Smart Watch first appeared on Sinocrystal.

1.3” 128×64 OLED With SH1106G IC, 30PIN

管理员 — Thu, 13 Aug 2020 07:10:51 +0000

Drawing

General Specification

ITEM	SPECIFICATIONS	UNIT
MODULE SIZE	34.5(W)x23.0(H)x1.427(D)	mm
VIEWING AREA	31.42 (W) x 16.7(H)	mm
ACTIVE AREA	29.42(W) x14.7(H)	mm
DOT SIZE	0.21(W) x0.21(H)	mm
DOT PITCH	0.23(W) x0.23 (H)	mm
ASSY.TYPE	COG	—
WEIGHT	TBD

Interface Definition

PIN NO.

SYMBOL

TYPE

FUNCTION DESCRIPTIONS

NC(GND)

It should be connected to external ground.

C2P

C1P/C1N-Pin for charge pump capacitor.
C2P/C2N-Pin for charge pump capacitor.
Connect to each other with a capacitor. They must be floated when the
Charge pump not use.

C2N

C1P

C1N

VBAT

Power supply for charge pump regulator circuit.
It must be connected to external source when charge pump is used. It must be float when charge pump is not used.

VSS

Ground pin. It must be connected to external ground.

VSS

VDD

Power pin for logic circuit. It must be connected to external source.

BS0

Interface selection pins.

	I2C	6800	8080	4SPI
BS0	0	0	0	0
BS1	1	0	1	0
BS2	0	1	1	0

BS1

BS2

CS#

Chip Select input pin. Active “L”

RES#

Hardware reset input pin. Active “L”.

D/C#

This is Data/Command control pin.
When the pin is pulled HIGH, the data at D[7:0] is data. When the pin is pulled LOW, the data at D[7:0] is command. In I2C mode, this pin acts as SA0 for slave address section.
When 3-wire serial interface is selected, this pin must be connected to VSS

R/W#

This is read/write control input pin.
8080: data write enable; 6800: read/write select pin.
When serial or I2C interface is selected, this pin must be connected to VSS.

This is read/write control input pin.
8080: data read enable; 6800: read/write enable pin.
When serial or I2C interface is selected, this pin must be connected to VSS.

I/O

These are 8-bit bi-directional data bus to be connected to microprocessor’s Data bus.
When serial interface mode is selected, D2 should be kept NC, D1 will be the serial data input: SDIN, D0 will be the serial clock input: SCLK.
When I2C mode is selected, D2, D1 should be tied together and serve as SDA and D0 is the serial clock input, SCL.

IREF

Current reference for brightness adjustment.
This is segment output current reference pin. A resistor should be connected between this pin and VSS .Set the current at 12.5 uA maximum.

VCOMH

COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS.

VCC

Power supply for OLED driving voltage. A capacitor should be connected between this pin and VSS, when charge pump is used.
It must be connected to external source when charge pump is not used.

This is an analog ground pin. It should be connected to VSS externally.

NC(GND)

It should be connected to external ground.

The post 1.3'' 128×64 OLED With SH1106G IC, 30PIN first appeared on Sinocrystal.

0.96” 128×64 OLED With SSD1315Z IC, 30PIN, 3/4wire Serial Interface, I2C

管理员 — Thu, 13 Aug 2020 06:59:35 +0000

Drawing

General Specification

ITEM	SPECIFICATIONS	UNIT
MODULE SIZE	24.74(W)x16.9(H)x1.42(D)	mm
VIEWING AREA	22.74 (W) x 11.86(H)	mm
ACTIVE AREA	21.74 (W) x10.86(H)	mm
DOT SIZE	0.15(W) x0.15(H)	mm
DOT PITCH	0.17(W) x0.17 (H)	mm
ASSY.TYPE	COG	—
WEIGHT	TBD

Interface Definition

PIN NO.

SYMBOL

TYPE

FUNCTION DESCRIPTIONS

NC(GND)

It should be connected to external ground.

C2P

C1P/C1N-Pin for charge pump capacitor.
C2P/C2N-Pin for charge pump capacitor.
Connect to each other with a capacitor. They must be floated when the
Charge pump not use.

C2N

C1P

C1N

VBAT

Power supply for charge pump regulator circuit.
It must be connected to external source when charge pump is used. It must be float when charge pump is not used.

VSS

Ground pin. It must be connected to external ground.

VDD

Power pin for logic circuit. It must be connected to external source.

BS0

Interface selection pins.

	BS0	BS1
I2C	0	1
3-wire SPI	1	0
4-wire SPI	0	0

BS1

NC.

CS#

Chip Select input pin. Active “L”

RES#

Hardware reset input pin. Active “L”.

D/C#

NC.

I/O

When serial interface mode is selected,D2 should be either tied LOW or tied together with D1 as the serial data input: SDIN, and D0 will be the serial clock input: SCLK.
When I2C mode is selected, D2, D1 should be tied together and serve as SDA and D0
is the serial clock input, SCL.

NC.

IREF

Current reference for brightness adjustment.
This is segment output current reference pin. A resistor should be connected between this pin and VSS .Set the current at 12.5 uA maximum.

VCOMH

COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS.

VCC

Power supply for OLED driving voltage. A capacitor should be connected between this pin and VSS, when charge pump is used.
It must be connected to external source when charge pump is not used.

VLSS

This is an analog ground pin. It should be connected to VSS externally.

NC(GND)

It should be connected to external ground.

The post 0.96'' 128×64 OLED With SSD1315Z IC, 30PIN, 3/4wire Serial Interface, I2C first appeared on Sinocrystal.

0.96” 128×64 OLED With SSD1316BZ IC,30PIN 6800/8080 Interface, 4 Wire Serial I2C

管理员 — Thu, 13 Aug 2020 06:53:27 +0000

Drawing

General Specification

ITEM	SPECIFICATIONS	UNIT
MODULE SIZE	26.7(W)x19.26(H)x1.227(D)	mm
VIEWING AREA	23.74 (W) x 13.2(H)	mm
ACTIVE AREA	21.74(W) x11.2 (H)	mm
DOT SIZE	0.15(W) x0.15(H)	mm
DOT PITCH	0.17(W) x0.17 (H)	mm
ASSY.TYPE	COG	—
WEIGHT	TBD

Interface Definition

PIN NO.

SYMBOL

TYPE

FUNCTION DESCRIPTIONS

NC(GND)

It should be connected to external ground.

C2P

C1P/C1N-Pin for charge pump capacitor.
C2P/C2N-Pin for charge pump capacitor.
Connect to each other with a capacitor. They must be floated when the
Charge pump not use.

C2N

C1P

C1N

VBAT

Power supply for charge pump regulator circuit.
It must be connected to external source when charge pump is used. It must be float when charge pump is not used.

VSS

Ground pin. It must be connected to external ground.

VDD

Power pin for logic circuit. It must be connected to external source.

BS0

Interface selection pins.

	I2C	6800	8080	4SPI
BS0	0	0	0	0
BS1	1	0	1	0
BS2	0	1	1	0

BS1

BS2

CS#

Chip Select input pin. Active “L”

RES#

Hardware reset input pin. Active “L”.

D/C#

R/W#

This is read/write control input pin.
8080: data write enable; 6800: read/write select pin.
When serial or I2C interface is selected, this pin must be connected to VSS.

This is read/write control input pin.
8080: data read enable; 6800: read/write enable pin.
When serial or I2C interface is selected, this pin must be connected to VSS.

I/O

IREF

Current reference for brightness adjustment.
This is segment output current reference pin. A resistor should be connected between this pin and VSS .Set the current at 12.5 uA maximum.

VCOMH

COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS.

VCC

Power supply for OLED driving voltage. A capacitor should be connected between this pin and VSS, when charge pump is used.
It must be connected to external source when charge pump is not used.

VLSS

This is an analog ground pin. It should be connected to VSS externally.

NC(GND)

It should be connected to external ground.

The post 0.96'' 128×64 OLED With SSD1316BZ IC,30PIN 6800/8080 Interface, 4 Wire Serial I2C first appeared on Sinocrystal.

0.96 Inch Mono OLED With 128×64, SSD1316BZ IC,30PIN, 6800/8080 Interface, 4 Wire Serial Interface, I2C

管理员 — Thu, 13 Aug 2020 06:49:23 +0000

Drawing

General Specification

ITEM	SPECIFICATIONS	UNIT
MODULE SIZE	26.7(W)x19.26(H)x1.227(D)	mm
VIEWING AREA	23.74 (W) x 13.2(H)	mm
ACTIVE AREA	21.74(W) x11.2 (H)	mm
DOT SIZE	0.15(W) x0.15(H)	mm
DOT PITCH	0.17(W) x0.17 (H)	mm
ASSY.TYPE	COG	—
WEIGHT	TBD

Interface Definition

PIN NO.

SYMBOL

TYPE

FUNCTION DESCRIPTIONS

NC(GND)

It should be connected to external ground.

C2P

C1P/C1N-Pin for charge pump capacitor.
C2P/C2N-Pin for charge pump capacitor.
Connect to each other with a capacitor. They must be floated when the
Charge pump not use.

C2N

C1P

C1N

VBAT

Power supply for charge pump regulator circuit.
It must be connected to external source when charge pump is used. It must be float when charge pump is not used.

VSS

Ground pin. It must be connected to external ground.

VDD

Power pin for logic circuit. It must be connected to external source.

BS0

Interface selection pins.

	I2C	6800	8080	4SPI
BS0	0	0	0	0
BS1	1	0	1	0
BS2	0	1	1	0

BS1

BS2

CS#

Chip Select input pin. Active “L”

RES#

Hardware reset input pin. Active “L”.

D/C#

R/W#

This is read/write control input pin.
8080: data write enable; 6800: read/write select pin.
When serial or I2C interface is selected, this pin must be connected to VSS.

This is read/write control input pin.
8080: data read enable; 6800: read/write enable pin.
When serial or I2C interface is selected, this pin must be connected to VSS.

I/O

IREF

Current reference for brightness adjustment.
This is segment output current reference pin. A resistor should be connected between this pin and VSS .Set the current at 12.5 uA maximum.

VCOMH

COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS.

VCC

Power supply for OLED driving voltage. A capacitor should be connected between this pin and VSS, when charge pump is used.
It must be connected to external source when charge pump is not used.

VLSS

This is an analog ground pin. It should be connected to VSS externally.

NC(GND)

It should be connected to external ground.

The post 0.96 Inch Mono OLED With 128×64, SSD1316BZ IC,30PIN, 6800/8080 Interface, 4 Wire Serial Interface, I2C first appeared on Sinocrystal.

0.96” OLED Display With 128×64 Resolution SSD1316BZ IC,30PIN, 6800/8080 Interface, 4 Wire Serial Interface, I2C

管理员 — Thu, 13 Aug 2020 06:42:47 +0000

Drawing

General Specification

ITEM	SPECIFICATIONS	UNIT
MODULE SIZE	26.7(W)x19.26(H)x1.227(D)	mm
VIEWING AREA	23.74 (W) x 13.2(H)	mm
ACTIVE AREA	21.74(W) x11.2 (H)	mm
DOT SIZE	0.15(W) x0.15(H)	mm
DOT PITCH	0.17(W) x0.17 (H)	mm
ASSY.TYPE	COG	—
WEIGHT	TBD

Interface Definition

PIN NO.	SYMBOL	TYPE	FUNCTION DESCRIPTIONS
1	NC(GND)	P	It should be connected to external ground.
2	C2P		C1P/C1N-Pin for charge pump capacitor. C2P/C2N-Pin for charge pump capacitor. Connect to each other with a capacitor. They must be floated when the Charge pump not use.
3	C2N
4	C1P	I
5	C1N
6	VBAT	P	Power supply for charge pump regulator circuit. It must be connected to external source when charge pump is used. It must be float when charge pump is not used.
7	NC		NC
8	VSS	P	Ground pin. It must be connected to external ground.
9	VDD	P	Power pin for logic circuit. It must be connected to external source.
10	BS0	I	Interface selection pins.
11	BS1
12	BS2
13	CS#	I	Chip Select input pin. Active “L”
14	RES#	I	Hardware reset input pin. Active “L”.
15	D/C#	I	This is Data/Command control pin. When the pin is pulled HIGH, the data at D[7:0] is data. When the pin is pulled LOW, the data at D[7:0] is command. In I2C mode, this pin acts as SA0 for slave address section. When 3-wire serial interface is selected, this pin must be connected to VSS
16	R/W#	I	This is read/write control input pin. 8080: data write enable; 6800: read/write select pin. When serial or I2C interface is selected, this pin must be connected to VSS.
17	E#	I	This is read/write control input pin. 8080: data read enable; 6800: read/write enable pin. When serial or I2C interface is selected, this pin must be connected to VSS.
18	D0	I/O	These are 8-bit bi-directional data bus to be connected to microprocessor’s Data bus. When serial interface mode is selected, D2 should be kept NC, D1 will be the serial data input: SDIN, D0 will be the serial clock input: SCLK. When I2C mode is selected, D2, D1 should be tied together and serve as SDA and D0 is the serial clock input, SCL.
19	D1
20	D2
21	D3
22	D4
23	D5
24	D6
25	D7
26	IREF	I	Current reference for brightness adjustment. This is segment output current reference pin. A resistor should be connected between this pin and VSS .Set the current at 12.5 uA maximum.
27	VCOMH	O	COM signal deselected voltage level. A capacitor should be connected between this pin and VSS.
28	VCC	P	Power supply for OLED driving voltage. A capacitor should be connected between this pin and VSS, when charge pump is used. It must be connected to external source when charge pump is not used.
29	VLSS	P	This is an analog ground pin. It should be connected to VSS externally.
30	NC(GND)	P	It should be connected to external ground.

The post 0.96'' OLED Display With 128×64 Resolution SSD1316BZ IC,30PIN, 6800/8080 Interface, 4 Wire Serial Interface, I2C first appeared on Sinocrystal.

0.66 Inch OLED Display With 64×48 Resolution SSD1306BZ IC, 30PIN

管理员 — Thu, 13 Aug 2020 06:21:37 +0000

Drawing

General Specification

ITEM	SPECIFICATIONS	UNIT
MODULE SIZE	18.46(W)x18.1(H)x1.21(D)	mm
VIEWING AREA	15.42 (W) x 12.06(H)	mm
ACTIVE AREA	13.42 (W) x10.06(H)	mm
DOT SIZE	0.19(W) x0.19(H)	mm
DOT PITCH	0.21(W) x0.21 (H)	mm
ASSY.TYPE	COG	—
WEIGHT	TBD

Interface Definition

PIN NO.	SYMBOL	TYPE	FUNCTION DESCRIPTIONS
1	NC		NC.
2	C2P		C1P/C1N-Pin for charge pump capacitor. C2P/C2N-Pin for charge pump capacitor. Connect to each other with a capacitor. They must be floated when the Charge pump not use.
3	C2N
4	C1P	I
5	C1N
6	VBAT	P	Power supply for charge pump regulator circuit. It must be connected to external source when charge pump is used. It must be float when charge pump is not used.
7	NC		NC.
8	VSS	P	Ground pin. It must be connected to external ground.
9	VDD	P	Power pin for logic circuit. It must be connected to external source.
10	NC		NC.
11	BS1	I	Bitmap Interface selection pins.
12	BS2	I	Bitmap Interface selection pins.
13	CS#	I	Chip Select input pin. Active “L”
14	RES#	I	Hardware reset input pin. Active “L”.
15	D/C#	I	This is Data/Command control pin. When the pin is pulled HIGH, the data at D[7:0] is data. When the pin is pulled LOW, the data at D[7:0] is command. In I2C mode, this pin acts as SA0 for slave address section. When 3-wire serial interface is selected, this pin must be connected to VSS
16	R/W#	I	This is read/write control input pin. 8080: data write enable; 6800: read/write select pin. When serial or I2C interface is selected, this pin must be connected to VSS.
17	E/RD#	I	This is read/write control input pin. 8080: data read enable; 6800: read/write enable pin. When serial or I2C interface is selected, this pin must be connected to VSS.
18	D0	I/O	These are 8-bit bi-directional data bus to be connected to microprocessor’s Data bus. When serial interface mode is selected, D2 should be kept NC, D1 will be the serial data input: SDIN, D0 will be the serial clock input: SCLK. When I2C mode is selected, D2, D1 should be tied together and serve as SDA and D0 is the serial clock input, SCL.
19	D1
20	D2
21	D3
22	D4
23	D5
24	D6
25	D7
26	IREF	I	Current reference for brightness adjustment. This is segment output current reference pin. A resistor should be connected between this pin and VSS .Set the current at 12.5 uA maximum.
27	VCOMH	O	COM signal deselected voltage level. A capacitor should be connected between this pin and VSS.
28	VCC	P	Power supply for OLED driving voltage. A capacitor should be connected between this pin and VSS, when charge pump is used. It must be connected to external source when charge pump is not used.
29	NC		NC.
30	NC		NC.

The post 0.66 Inch OLED Display With 64×48 Resolution SSD1306BZ IC, 30PIN first appeared on Sinocrystal.