– – Sinocrystal https://sinocrystal.net Fri, 25 Feb 2022 08:44:12 +0000 en-US hourly 1 https://wordpress.org/?v=5.3.16 https://sinocrystal.net/wp-content/uploads/2020/06/logo_small-100x100.png – – Sinocrystal https://sinocrystal.net 32 32 2.7” 128×64 OLED With SPD0301ZD IC, 24PIN https://sinocrystal.net/product/2-7-128x64-oled-with-spd0301zd-ic-24pin Tue, 26 Jan 2021 01:38:09 +0000 https://sinocrystal.net/?post_type=product&p=5007 SCE270001-V01 is a OLED Display with 128×64 Resolution, SSD1325 IC, 6800/8080 interface, 4 wire serial interface, I2C, 30PIN

The post 2.7'' 128×64 OLED With SPD0301ZD IC, 24PIN first appeared on Sinocrystal.

]]>  

                         Drawing

 

 

 

 

 

                         General Specification

 

ITEM SPECIFICATIONS  UNIT
 MODULE SIZE 89.70 × 47.20 × 3.40 mm
 VIEWING AREA 73.00 × 41.86 × 2.00 mm
 ACTIVE AREA 61.41 × 30.69 mm
 DOT SIZE 0.45 × 0.45 mm
 DOT PITCH 0.48 × 0.48 mm
 Resolution 128 x 64 —
Display Color Monochrome (Yellow / 16 Gray Scales)

 

The post 2.7'' 128×64 OLED With SPD0301ZD IC, 24PIN first appeared on Sinocrystal.

]]> 1.54” 128×64 OLED With SPD0301ZD IC, 24PIN https://sinocrystal.net/product/1-54-128x64-oled-with-spd0301zd-ic-24pin-6800-8080-interface-4-wire-serial-interface-i2c Thu, 13 Aug 2020 08:12:29 +0000 https://www.sinocrystal.net/?post_type=product&p=1577 SCE154001-V01 is a OLED Display with COG Type, 128×64 Resolution, SPD0301ZD IC, 6800/8080 interface, 4 wire serial interface, I2C, 30PIN

The post 1.54'' 128×64 OLED With SPD0301ZD IC, 24PIN first appeared on Sinocrystal.

]]>  

                         Drawing

 

 

 

 

                         General Specification

 

ITEM SPECIFICATIONS  UNIT
 MODULE SIZE 42.04(W)x27.22(H)x1.41(D) mm
 VIEWING AREA 37.052 (W) x 19.516(H) mm
 ACTIVE AREA 35.052(W) x17.516(H) mm
 DOT SIZE 0.254(W) x0.254(H) mm
 DOT PITCH 0.274(W) x0.274 (H) mm
 ASSY.TYPE COG —
 WEIGHT TBD

 

 

 

 

                         Interface Definition

 

PIN NO. SYMBOL TYPE FUNCTION DESCRIPTIONS
1 NC(GND) P It should be connected to external ground.
2 VLSS P This is an analog ground pin. It should be connected to VSS externally.
3 VSS P Ground pin. It must be connected to external ground.
4 NC NC
5 VDD P Power pin for logic circuit. It must be connected to external source.
6 BS1 I

Interface selection pins.

I2C 6800 8080 4SPI
BS1 1 0 1 0
BS2 0 1 1 0
7 BS2
8 CS# I Chip Select input pin. Active “L”
9 RES# I Hardware reset input pin. Active “L”.
10 D/C# I WThis is Data/Command control pin.
When the pin is pulled HIGH, the data at D[7:0]  is data.
When the pin is pulled LOW, the data at D[7:0] is command. In I2C mode, this pin acts as SA0 for slave address section.
When 3-wire serial interface is selected, this pin must be connected to VSS
11 R/W# I This is read/write control input pin.
8080: data write enable; 6800: read/write select pin.
When serial or I2C interface is selected, this pin must be connected to VSS.
12 E/RD# I This is read/write control input pin.
8080: data read enable; 6800: read/write enable pin.
When serial or I2C interface is selected, this pin must be connected to VSS.
13 D0 I/O These are 8-bit bi-directional data bus to be connected to microprocessor’s Data bus.
When serial interface mode is selected, D2 should be kept NC, D1 will be the serial data input: SDIN, D0 will be the serial clock input: SCLK.
When I2C mode is selected, D2, D1 should be tied together and serve as SDA and D0 is the serial clock input, SCL.
14 D1
15 D2
16 D3
17 D4
18 D5
19 D6
20 D7
21 IREF I Current reference for brightness adjustment.
This is segment output current reference pin. A resistor should be connected between this pin and VSS .Set the current at 10 uA maximum.
22 VCOMH O COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS.
23 VCC P Power supply for OLED driving voltage. A capacitor should be connected between this pin and VSS.
24 NC(GND) P It should be connected to external ground.

The post 1.54'' 128×64 OLED With SPD0301ZD IC, 24PIN first appeared on Sinocrystal.

]]> 1.4'' Round OLED For Smart Watch With 454*454 Resolution RM69330 IC, 24PIN, MIPI/SPI Interface https://sinocrystal.net/product/1-4-round-oled-for-smart-watch-with-454454-resolution-rm69330-ic-24pin-mipi-spi-interface Thu, 13 Aug 2020 07:47:29 +0000 https://www.sinocrystal.net/?post_type=product&p=1569 SCE140001-V01 is a Round OLED Display with COG Type, 454*454 Resolution, RM69330 IC, MIPI/SPI interface, 24 PIN

The post 1.4'' Round OLED For Smart Watch With 454*454 Resolution RM69330 IC, 24PIN, MIPI/SPI Interface first appeared on Sinocrystal.

]]>  

                         Description

                         This 1.4″ circular OLED display with beautiful shape will take your eyes at first glance.

                         The high resolution, vibrant colors, excellent contrast, and thin profile will surprised you when you have the flexible Amoled display.

                         If you are creating a wearable, the wide viewing angles, low profile and low power consumption will give you a competitive advantage.

                         If you are designing a medical device, the high resolution and amazing contrast will provide the necessary accuracy.

 

 

 

                         Drawing

 

 

 

 

 

 

                         General Specification

 

 

Item Specification unit
Dimension outline 38.83(V) x 38.21(W) x 0.68(T) mm
LTPS Glass outline 38.83(V) x 38.21(W) mm
Encapsulation Glass outline φ38.21 mm
Number of dots 454(W) x RGB x 454(H) dots
Active area φ35.412 mm
Diagonal size 1.39 inch
Pixel pitch 78 x 78 μm
Glass thickness 0.2 / 0.2 mm

 

 

 

 

                         Interface Definition

 

 

Part No. Pin name I/O Description
1 XRES I Device reset signal (0 : enable ; 1 : Disable)
2 VCI_EN I VCI enable signal
3 VPP – OTP
4 GND Power Ground
5 TE O Synchronous signal output from panel to avoid tearing effect
6 DSI_D0N I/O MIPI data negative signal
7 AM_SPI_CSX I SPI interface
8 DSI_D0P I/O MIPI data positive signal
9 AM_SPI_SCL I SPI interface
10 GND Power Ground
11 AM_SPI_DCX I SPI interface
12 DSI_CLKN I MIPI strobe negative signal
13 AM_SPI_SDI I/O SPI interface
14 DSI_CLKP I MIPI strobe positive signal
15 AM_SPI_SDO I/O SPI interface
16 GND Power Ground
17 NC – Floating
18 VDDIO Power Power supply for interface system except MIPI interface
19 VBAT Power AMOLED power
20 VDDIO Power Power supply for interface system except MIPI interface
21 VBAT Power AMOLED power
22 VBAT Power AMOLED power
23 VBAT Power AMOLED power
24 VBAT Power AMOLED power

The post 1.4'' Round OLED For Smart Watch With 454*454 Resolution RM69330 IC, 24PIN, MIPI/SPI Interface first appeared on Sinocrystal.

]]> 1.41'' OLED With 320*360 Dot Matrix ZTW522 IC, 30PIN, MIPI Interface For Smart Watch https://sinocrystal.net/product/1-41-oled-with-320360-dot-matrix-ztw522-ic-30pin-mipi-interface-for-smart-watch Thu, 13 Aug 2020 07:16:17 +0000 https://www.sinocrystal.net/?post_type=product&p=1566 SCE0141001-V01 is a OLED Display with COG Type, 320x360 Resolution,TP ZTW522 IC, MIPI interface, 30PIN

The post 1.41'' OLED With 320*360 Dot Matrix ZTW522 IC, 30PIN, MIPI Interface For Smart Watch first appeared on Sinocrystal.

]]>  

 

                         Drawing

 

1.4'' oled display

                         General Specification

 

ITEM SPECIFICATIONS  UNIT
 MODULE SIZE 26.04×31.78 mm
 VIEWING AREA 26.04 x30.18 mm
 ACTIVE AREA 23.84×26.82 mm
 DOT SIZE 0.21(W) x0.21(H) mm
 DOT PITCH 0.23(W) x0.23 (H) mm
 ASSY.TYPE COG —
 WEIGHT TBD

 

 

 

                         Interface Definition

 

# Pin name I/O Description
1 TP_INT I/O Interrupt to Host
2 TP_SDA I/O I2C Data Line
3 TP_SCL I/O I2C Clock Line
4 TP_VDD Power TP Power Supply
5 ELVDD Power Power supply for OLED
6 VDD1 Power Driver IC analog supply
7 SWIRE O Power IC control signal
8 GND1 Power GND
9 REST I This signal will reset the device and must be applied to properly initialize the chip.
Active low.
10 NC – No connector
11 NC – No connector
12 NC – No connector
13 NC – No connector
14 NC – No connector
15 GND2 Power GND
16 NC – No connector
17 GND3 Power GND
18 DSI_D0N I/O MIPI DSI data0+
19 DSI_D0P I/O MIPI DSI data0-
20 GND4 Power GND
21 DSI_CLKN I/O MIPI DSI clock-
22 DSI_CLKP I/O MIPI DSI clock+
23 GND5 Power GND
24 VDDIO Power Driver IC digital I/O supply.
25 TE O Tear effect output
26 VDD2 Power Driver IC analog supply
27 ELVSS Power Power supply for OLED
28 GND6 Power GND
29 TP_RST I Reset
30 GND7 Power GND

The post 1.41'' OLED With 320*360 Dot Matrix ZTW522 IC, 30PIN, MIPI Interface For Smart Watch first appeared on Sinocrystal.

]]> 1.3” 128×64 OLED With SH1106G IC, 30PIN https://sinocrystal.net/product/1-3-128x64-oled-with-sh1106g-ic-30pin-6800-8080-interface-4-wire-serial-interface-i2c Thu, 13 Aug 2020 07:10:51 +0000 https://www.sinocrystal.net/?post_type=product&p=1563 SCE0130001-V01 is a OLED Display with COG Type, 128×64 Resolution, SH1106G IC, 6800/8080 interface, 4 wire serial interface, I2C, 30PIN

The post 1.3'' 128×64 OLED With SH1106G IC, 30PIN first appeared on Sinocrystal.

]]>  

                         Drawing

 

1.3'' OLED Display

 

 

                         General Specification

 

ITEM SPECIFICATIONS  UNIT
 MODULE SIZE 34.5(W)x23.0(H)x1.427(D) mm
 VIEWING AREA 31.42 (W) x 16.7(H) mm
 ACTIVE AREA 29.42(W) x14.7(H) mm
 DOT SIZE 0.21(W) x0.21(H) mm
 DOT PITCH 0.23(W) x0.23 (H) mm
 ASSY.TYPE COG —
 WEIGHT TBD

 

 

 

 

 

                         Interface Definition

 

PIN NO. SYMBOL TYPE FUNCTION DESCRIPTIONS
1 NC(GND) P It should be connected to external ground.
2 C2P I C1P/C1N-Pin for charge pump capacitor.
C2P/C2N-Pin for charge pump capacitor.
Connect to each other with a capacitor. They must be floated when the
Charge pump not use.
3 C2N
4 C1P
5 C1N
6 VBAT P Power supply for charge pump regulator circuit.
It must be connected to external source when charge pump is used. It must be float when charge pump is not used.
7 VSS P Ground pin. It must be connected to external ground.
8 VSS
9 VDD P Power pin for logic circuit. It must be connected to external source.
10 BS0 I Interface selection pins.

 

I2C 6800 8080 4SPI
BS0 0 0 0 0
BS1 1 0 1 0
BS2 0 1 1 0
11 BS1
12 BS2
13 CS# I Chip Select input pin. Active “L”
14 RES# I Hardware reset input pin. Active “L”.
15 D/C# I This is Data/Command control pin.
When the pin is pulled HIGH, the data at D[7:0]  is data. When the pin is pulled LOW, the data at D[7:0] is command. In I2C mode, this pin acts as SA0 for slave address section.
When 3-wire serial interface is selected, this pin must be connected to VSS
16 R/W# I This is read/write control input pin.
8080: data write enable; 6800: read/write select pin.
When serial or I2C interface is selected, this pin must be connected to VSS.
17 E# I This is read/write control input pin.
8080: data read enable; 6800: read/write enable pin.
When serial or I2C interface is selected, this pin must be connected to VSS.
18 D0 I/O These are 8-bit bi-directional data bus to be connected to microprocessor’s Data bus.
When serial interface mode is selected, D2 should be kept NC, D1 will be the serial data input: SDIN, D0 will be the serial clock input: SCLK.
When I2C mode is selected, D2, D1 should be tied together and serve as SDA and D0 is the serial clock input, SCL.
19 D1
20 D2
21 D3
22 D4
23 D5
24 D6
25 D7
26 IREF O Current reference for brightness adjustment.
This is segment output current reference pin. A resistor should be connected between this pin and VSS .Set the current at 12.5 uA maximum.
27 VCOMH O COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS.
28 VCC P Power supply for OLED driving voltage. A capacitor should be connected between this pin and VSS, when charge pump is used.
It must be connected to external source when charge pump is not used.
29 NC This is an analog ground pin. It should be connected to VSS externally.
30 NC(GND) P It should be connected to external ground.

 

The post 1.3'' 128×64 OLED With SH1106G IC, 30PIN first appeared on Sinocrystal.

]]> 0.96'' Vertical 64×128 OLED Display With SH1107 IC, 13PIN, 4wire Serial Interface, I2C https://sinocrystal.net/product/0-96-vertical-64x128-oled-display-with-sh1107-ic-13pin-4wire-serial-interface-i2c Thu, 13 Aug 2020 07:06:50 +0000 https://www.sinocrystal.net/?post_type=product&p=1560 SCE096013-V01 is a Vertical OLED Display with COG Type, 64x128 Resolution, SH1107 IC, 4wire serial interface, I2C, 13PIN

The post 0.96'' Vertical 64x128 OLED Display With SH1107 IC, 13PIN, 4wire Serial Interface, I2C first appeared on Sinocrystal.

]]>                           Drawing

 

 

 

 

                         General Specification

 

ITEM SPECIFICATIONS  UNIT
  MODULE SIZE 24.74(W)x16.9(H)x1.42(D) mm
  VIEWING AREA 22.74 (W) x 11.86(H) mm
  ACTIVE AREA 21.74 (W) x10.86(H) mm
  DOT SIZE 0.15(W) x0.15(H) mm
  DOT PITCH 0.17(W) x0.17 (H) mm
  ASSY.TYPE COG —
  WEIGHT TBD

 

 

 

 

 

                         Interface Definition

 

PIN NO. SYMBOL TYPE FUNCTION DESCRIPTIONS
1 NC(GND) P It should be connected to external ground.
2 C2P C1P/C1N-Pin for charge pump capacitor.
C2P/C2N-Pin for charge pump capacitor.
Connect to each other with a capacitor. They must be floated when the
Charge pump not use.
3 C2N
4 C1P I
5 C1N
6 VBAT P Power supply for charge pump regulator circuit.
It must be connected to external source when charge pump is used. It must be float when charge pump is not used.
7 NC NC
8 VSS P Ground pin. It must be connected to external ground.
9 VDD P Power pin for logic circuit. It must be connected to external source.
10 BS0 I Interface selection pins.

 

BS0 BS1
I2C 0 1
3-wire SPI 1 0
4-wire SPI 0 0
11 BS1
12 NC NC.
13 CS# I Chip Select input pin. Active “L”
14 RES# I Hardware reset input pin. Active “L”.
15 D/C# I This is Data/Command control pin.
When the pin is pulled HIGH, the data at D[7:0]  is data. When the pin is pulled LOW, the data at D[7:0] is command. In I2C mode, this pin acts as SA0 for slave address section.
When 3-wire serial interface is selected, this pin must be connected to VSS
16 NC NC.
17 NC NC.
18 D0 I/O When serial interface mode is selected,D2 should be either tied LOW or tied together with D1 as the serial data input: SDIN, and D0 will be the serial clock input: SCLK.
When I2C mode is selected, D2, D1 should be tied together and serve as SDA and D0
is the serial clock input, SCL.
19 D1
20 D2
22 NC NC.
23 NC NC.
24 NC NC.
25 NC NC.
26 IREF I Current reference for brightness adjustment.
This is segment output current reference pin. A resistor should be connected between this pin and VSS .Set the current at 12.5 uA maximum.
27 VCOMH O COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS.
28 VCC P Power supply for OLED driving voltage. A capacitor should be connected between this pin and VSS, when charge pump is used.
It must be connected to external source when charge pump is not used.
29 VLSS P This is an analog ground pin. It should be connected to VSS externally.
30 NC(GND) P It should be connected to external ground.

The post 0.96'' Vertical 64x128 OLED Display With SH1107 IC, 13PIN, 4wire Serial Interface, I2C first appeared on Sinocrystal.

]]> 0.96” 128×64 OLED With SSD1315Z IC, 30PIN, 3/4wire Serial Interface, I2C https://sinocrystal.net/product/0-96-128x64-oled-with-ssd1315z-ic-30pin-3-4wire-serial-interface-i2c Thu, 13 Aug 2020 06:59:35 +0000 https://www.sinocrystal.net/?post_type=product&p=1557 SCE096009-V01 is a OLED Display with COG Type, 128×64 Resolution, SSD1315Z IC, 3/4wire serial interface, I2C, 30PIN

The post 0.96'' 128×64 OLED With SSD1315Z IC, 30PIN, 3/4wire Serial Interface, I2C first appeared on Sinocrystal.

]]>                           Drawing

 

 

 

 

                         General Specification

 

ITEM SPECIFICATIONS  UNIT
  MODULE SIZE 24.74(W)x16.9(H)x1.42(D) mm
  VIEWING AREA 22.74 (W) x 11.86(H) mm
  ACTIVE AREA 21.74 (W) x10.86(H) mm
  DOT SIZE 0.15(W) x0.15(H) mm
  DOT PITCH 0.17(W) x0.17 (H) mm
  ASSY.TYPE COG —
  WEIGHT TBD

 

 

 

 

 

                         Interface Definition

 

PIN NO. SYMBOL TYPE FUNCTION DESCRIPTIONS
1 NC(GND) P It should be connected to external ground.
2 C2P C1P/C1N-Pin for charge pump capacitor.
C2P/C2N-Pin for charge pump capacitor.
Connect to each other with a capacitor. They must be floated when the
Charge pump not use.
3 C2N
4 C1P I
5 C1N
6 VBAT P Power supply for charge pump regulator circuit.
It must be connected to external source when charge pump is used. It must be float when charge pump is not used.
7 NC NC
8 VSS P Ground pin. It must be connected to external ground.
9 VDD P Power pin for logic circuit. It must be connected to external source.
10 BS0 I Interface selection pins.

BS0 BS1
I2C 0 1
3-wire SPI 1 0
4-wire SPI 0 0
11 BS1
12 NC NC.
13 CS# I Chip Select input pin. Active “L”
14 RES# I Hardware reset input pin. Active “L”.
15 D/C# I This is Data/Command control pin.
When the pin is pulled HIGH, the data at D[7:0]  is data. When the pin is pulled LOW, the data at D[7:0] is command. In I2C mode, this pin acts as SA0 for slave address section.
When 3-wire serial interface is selected, this pin must be connected to VSS
16 NC NC.
17 NC NC.
18 D0 I/O When serial interface mode is selected,D2 should be either tied LOW or tied together with D1 as the serial data input: SDIN, and D0 will be the serial clock input: SCLK.
When I2C mode is selected, D2, D1 should be tied together and serve as SDA and D0
is the serial clock input, SCL.
19 D1
20 D2
22 NC NC.
23 NC NC.
24 NC NC.
25 NC NC.
26 IREF I Current reference for brightness adjustment.
This is segment output current reference pin. A resistor should be connected between this pin and VSS .Set the current at 12.5 uA maximum.
27 VCOMH O COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS.
28 VCC P Power supply for OLED driving voltage. A capacitor should be connected between this pin and VSS, when charge pump is used.
It must be connected to external source when charge pump is not used.
29 VLSS P This is an analog ground pin. It should be connected to VSS externally.
30 NC(GND) P It should be connected to external ground.

The post 0.96'' 128×64 OLED With SSD1315Z IC, 30PIN, 3/4wire Serial Interface, I2C first appeared on Sinocrystal.

]]> 0.96” 128×64 OLED With SSD1316 IC, 15PIN, 4 SPI Interface https://sinocrystal.net/product/0-96-128x64-oled-with-ssd1316-ic-15pin-4-spi-interface Thu, 13 Aug 2020 06:55:26 +0000 https://www.sinocrystal.net/?post_type=product&p=1554 SCE096006-V01 is a OLED Display with COG Type, 128×64 Resolution, SSD1306 IC, 4 SPI interface, 15PIN

The post 0.96'' 128×64 OLED With SSD1316 IC, 15PIN, 4 SPI Interface first appeared on Sinocrystal.

]]>  

 

                         General Specification

 

 

ITEM SPECIFICATIONS  UNIT
  MODULE SIZE 26.7(W)x19.26(H)x1.227(D) mm
  VIEWING AREA 23.74 (W) x 13.2(H) mm
  ACTIVE AREA 21.74(W) x11.2 (H) mm
  DOT SIZE 0.15(W) x0.15(H) mm
  DOT PITCH 0.17(W) x0.17 (H) mm
  ASSY.TYPE COG —
  WEIGHT TBD

 

 

 

 

 

                         Interface Definition

 

 

PIN NO. SYMBOL TYPE FUNCTION DESCRIPTIONS
1 NC(GND) P It should be connected to external ground.
2 C2P C1P/C1N-Pin for charge pump capacitor.
C2P/C2N-Pin for charge pump capacitor.
Connect to each other with a capacitor. They must be floated when the
Charge pump not use.
3 C2N
4 C1P I
5 C1N
6 VBAT P Power supply for charge pump regulator circuit.
It must be connected to external source when charge pump is used. It must be float when charge pump is not used.
7 NC NC
8 VSS P Ground pin. It must be connected to external ground.
9 VDD P Power pin for logic circuit. It must be connected to external source.
10 BS0 I Interface selection pins.

I2C 6800 8080 4SPI
BS0 0 0 0 0
BS1 1 0 1 0
BS2 0 1 1 0
11 BS1
12 BS2
13 CS# I Chip Select input pin. Active “L”
14 RES# I Hardware reset input pin. Active “L”.
15 D/C# I This is Data/Command control pin.
When the pin is pulled HIGH, the data at D[7:0]  is data. When the pin is pulled LOW, the data at D[7:0] is command. In I2C mode, this pin acts as SA0 for slave address section.
When 3-wire serial interface is selected, this pin must be connected to VSS
16 R/W# I This is read/write control input pin.
8080: data write enable; 6800: read/write select pin.
When serial or I2C interface is selected, this pin must be connected to VSS.
17 E# I This is read/write control input pin.
8080: data read enable; 6800: read/write enable pin.
When serial or I2C interface is selected, this pin must be connected to VSS.
18 D0 I/O These are 8-bit bi-directional data bus to be connected to microprocessor’s Data bus.
When serial interface mode is selected, D2 should be kept NC, D1 will be the serial data input: SDIN, D0 will be the serial clock input: SCLK.
When I2C mode is selected, D2, D1 should be tied together and serve as SDA and D0 is the serial clock input, SCL.
19 D1
20 D2
21 D3
22 D4
23 D5
24 D6
25 D7
26 IREF I Current reference for brightness adjustment.
This is segment output current reference pin. A resistor should be connected between this pin and VSS .Set the current at 12.5 uA maximum.
27 VCOMH O COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS.
28 VCC P Power supply for OLED driving voltage. A capacitor should be connected between this pin and VSS, when charge pump is used.
It must be connected to external source when charge pump is not used.
29 VLSS P This is an analog ground pin. It should be connected to VSS externally.
30 NC(GND) P It should be connected to external ground.

The post 0.96'' 128×64 OLED With SSD1316 IC, 15PIN, 4 SPI Interface first appeared on Sinocrystal.

]]> 0.96” 128×64 OLED With SSD1316BZ IC,30PIN 6800/8080 Interface, 4 Wire Serial I2C https://sinocrystal.net/product/0-96-128x64-oled-with-ssd1316bz-ic30pin-6800-8080-interface-4-wire-serial-i2c Thu, 13 Aug 2020 06:53:27 +0000 https://www.sinocrystal.net/?post_type=product&p=1553 SCE096004-V01 is a OLED Display with COG Type, 128×64 Resolution, SSD1306BZ IC, 4 wire serial interface, 30PIN

The post 0.96'' 128×64 OLED With SSD1316BZ IC,30PIN 6800/8080 Interface, 4 Wire Serial I2C first appeared on Sinocrystal.

]]>                           Drawing

 

 

 

 

                         General Specification

 

ITEM SPECIFICATIONS  UNIT
  MODULE SIZE 26.7(W)x19.26(H)x1.227(D) mm
  VIEWING AREA 23.74 (W) x 13.2(H) mm
  ACTIVE AREA 21.74(W) x11.2 (H) mm
  DOT SIZE 0.15(W) x0.15(H) mm
  DOT PITCH 0.17(W) x0.17 (H) mm
  ASSY.TYPE COG —
  WEIGHT TBD

 

 

 

                         Interface Definition

 

PIN NO. SYMBOL TYPE FUNCTION DESCRIPTIONS
1 NC(GND) P It should be connected to external ground.
2 C2P C1P/C1N-Pin for charge pump capacitor.
C2P/C2N-Pin for charge pump capacitor.
Connect to each other with a capacitor. They must be floated when the
Charge pump not use.
3 C2N
4 C1P I
5 C1N
6 VBAT P Power supply for charge pump regulator circuit.
It must be connected to external source when charge pump is used. It must be float when charge pump is not used.
7 NC NC
8 VSS P Ground pin. It must be connected to external ground.
9 VDD P Power pin for logic circuit. It must be connected to external source.
10 BS0 I Interface selection pins.

I2C 6800 8080 4SPI
BS0 0 0 0 0
BS1 1 0 1 0
BS2 0 1 1 0
11 BS1
12 BS2
13 CS# I Chip Select input pin. Active “L”
14 RES# I Hardware reset input pin. Active “L”.
15 D/C# I This is Data/Command control pin.
When the pin is pulled HIGH, the data at D[7:0]  is data. When the pin is pulled LOW, the data at D[7:0] is command. In I2C mode, this pin acts as SA0 for slave address section.
When 3-wire serial interface is selected, this pin must be connected to VSS
16 R/W# I This is read/write control input pin.
8080: data write enable; 6800: read/write select pin.
When serial or I2C interface is selected, this pin must be connected to VSS.
17 E# I This is read/write control input pin.
8080: data read enable; 6800: read/write enable pin.
When serial or I2C interface is selected, this pin must be connected to VSS.
18 D0 I/O These are 8-bit bi-directional data bus to be connected to microprocessor’s Data bus.
When serial interface mode is selected, D2 should be kept NC, D1 will be the serial data input: SDIN, D0 will be the serial clock input: SCLK.
When I2C mode is selected, D2, D1 should be tied together and serve as SDA and D0 is the serial clock input, SCL.
19 D1
20 D2
21 D3
22 D4
23 D5
24 D6
25 D7
26 IREF I Current reference for brightness adjustment.
This is segment output current reference pin. A resistor should be connected between this pin and VSS .Set the current at 12.5 uA maximum.
27 VCOMH O COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS.
28 VCC P Power supply for OLED driving voltage. A capacitor should be connected between this pin and VSS, when charge pump is used.
It must be connected to external source when charge pump is not used.
29 VLSS P This is an analog ground pin. It should be connected to VSS externally.
30 NC(GND) P It should be connected to external ground.

The post 0.96'' 128×64 OLED With SSD1316BZ IC,30PIN 6800/8080 Interface, 4 Wire Serial I2C first appeared on Sinocrystal.

]]> 0.96 Inch Mono OLED With 128×64, SSD1316BZ IC,30PIN, 6800/8080 Interface, 4 Wire Serial Interface, I2C https://sinocrystal.net/product/0-96-inch-mono-oled-with-128x64-ssd1316bz-ic30pin-6800-8080-interface-4-wire-serial-interface-i2c Thu, 13 Aug 2020 06:49:23 +0000 https://www.sinocrystal.net/?post_type=product&p=1549 SCE096003-V01 is a OLED Display with COG Type, 128×64 Resolution, SSD1306BZ IC, 4 wire serial interface, 30PIN

The post 0.96 Inch Mono OLED With 128×64, SSD1316BZ IC,30PIN, 6800/8080 Interface, 4 Wire Serial Interface, I2C first appeared on Sinocrystal.

]]>                           Drawing

 

 

 

                         General Specification

 

ITEM SPECIFICATIONS  UNIT
  MODULE SIZE 26.7(W)x19.26(H)x1.227(D) mm
  VIEWING AREA 23.74 (W) x 13.2(H) mm
  ACTIVE AREA 21.74(W) x11.2 (H) mm
  DOT SIZE 0.15(W) x0.15(H) mm
  DOT PITCH 0.17(W) x0.17 (H) mm
  ASSY.TYPE COG —
  WEIGHT TBD

 

 

 

                         Interface Definition

 

PIN NO. SYMBOL TYPE FUNCTION DESCRIPTIONS
1 NC(GND) P It should be connected to external ground.
2 C2P C1P/C1N-Pin for charge pump capacitor.
C2P/C2N-Pin for charge pump capacitor.
Connect to each other with a capacitor. They must be floated when the
Charge pump not use.
3 C2N
4 C1P I
5 C1N
6 VBAT P Power supply for charge pump regulator circuit.
It must be connected to external source when charge pump is used. It must be float when charge pump is not used.
7 NC NC
8 VSS P Ground pin. It must be connected to external ground.
9 VDD P Power pin for logic circuit. It must be connected to external source.
10 BS0 I Interface selection pins.

I2C 6800 8080 4SPI
BS0 0 0 0 0
BS1 1 0 1 0
BS2 0 1 1 0
11 BS1
12 BS2
13 CS# I Chip Select input pin. Active “L”
14 RES# I Hardware reset input pin. Active “L”.
15 D/C# I This is Data/Command control pin.
When the pin is pulled HIGH, the data at D[7:0]  is data. When the pin is pulled LOW, the data at D[7:0] is command. In I2C mode, this pin acts as SA0 for slave address section.
When 3-wire serial interface is selected, this pin must be connected to VSS
16 R/W# I This is read/write control input pin.
8080: data write enable; 6800: read/write select pin.
When serial or I2C interface is selected, this pin must be connected to VSS.
17 E# I This is read/write control input pin.
8080: data read enable; 6800: read/write enable pin.
When serial or I2C interface is selected, this pin must be connected to VSS.
18 D0 I/O These are 8-bit bi-directional data bus to be connected to microprocessor’s Data bus.
When serial interface mode is selected, D2 should be kept NC, D1 will be the serial data input: SDIN, D0 will be the serial clock input: SCLK.
When I2C mode is selected, D2, D1 should be tied together and serve as SDA and D0 is the serial clock input, SCL.
19 D1
20 D2
21 D3
22 D4
23 D5
24 D6
25 D7
26 IREF I Current reference for brightness adjustment.
This is segment output current reference pin. A resistor should be connected between this pin and VSS .Set the current at 12.5 uA maximum.
27 VCOMH O COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS.
28 VCC P Power supply for OLED driving voltage. A capacitor should be connected between this pin and VSS, when charge pump is used.
It must be connected to external source when charge pump is not used.
29 VLSS P This is an analog ground pin. It should be connected to VSS externally.
30 NC(GND) P It should be connected to external ground.

The post 0.96 Inch Mono OLED With 128×64, SSD1316BZ IC,30PIN, 6800/8080 Interface, 4 Wire Serial Interface, I2C first appeared on Sinocrystal.

]]>