OLED da 1,54'' 128×64 con IC SPD0301ZD, 24PIN | Sinocrystal

OLED da 1,54 '' 128 × 64 con IC SPD0301ZD, 24PIN, interfaccia 6800/8080, interfaccia seriale a 4 fili, I2C

SCE154001-V01 è un display OLED con tipo COG, risoluzione 128 × 64, IC SPD0301ZD, interfaccia 6800/8080, interfaccia seriale a 4 fili, I2C, 30PIN

Inquiry Now
SKU: SCE154001-V01
Type: OLED
Mode: -
Product No.: SCE154001-V01
Size: 1.54''
Resolution: 128*64
Outline Dimension: 42.04*27.22*1.41
Active Area: 35.052*17.516
Interface: 6800/8080 Interface,4-wire serial interface,I2C
IC: SPD0301ZD
Brightness: -
Touch Screen: No
View Direction: -
Pin No.: 24
Shape: Rectangle

Descrizione

 

                         Disegno

 

1.54'' OLED

 

 

                         Specifiche generali

 

ITEM SPECIFICATIONS  UNIT
 MODULE SIZE 42.04(W)x27.22(H)x1.41(D) mm
 VIEWING AREA 37.052 (W) x 19.516(H) mm
 ACTIVE AREA 35.052(W) x17.516(H) mm
 DOT SIZE 0.254(W) x0.254(H) mm
 DOT PITCH 0.274(W) x0.274 (H) mm
 ASSY.TYPE COG —
 WEIGHT TBD

 

 

 

 

                         Definizione dell’interfaccia

 

PIN NO. SYMBOL TYPE FUNCTION DESCRIPTIONS
1 NC(GND) P It should be connected to external ground.
2 VLSS P This is an analog ground pin. It should be connected to VSS externally.
3 VSS P Ground pin. It must be connected to external ground.
4 NC NC
5 VDD P Power pin for logic circuit. It must be connected to external source.
6 BS1 I

Interface selection pins.

I2C 6800 8080 4SPI
BS1 1 0 1 0
BS2 0 1 1 0
7 BS2
8 CS# I Chip Select input pin. Active “L”
9 RES# I Hardware reset input pin. Active “L”.
10 D/C# I WThis is Data/Command control pin.
When the pin is pulled HIGH, the data at D[7:0]  is data.
When the pin is pulled LOW, the data at D[7:0] is command. In I2C mode, this pin acts as SA0 for slave address section.
When 3-wire serial interface is selected, this pin must be connected to VSS
11 R/W# I This is read/write control input pin.
8080: data write enable; 6800: read/write select pin.
When serial or I2C interface is selected, this pin must be connected to VSS.
12 E/RD# I This is read/write control input pin.
8080: data read enable; 6800: read/write enable pin.
When serial or I2C interface is selected, this pin must be connected to VSS.
13 D0 I/O These are 8-bit bi-directional data bus to be connected to microprocessor’s Data bus.
When serial interface mode is selected, D2 should be kept NC, D1 will be the serial data input: SDIN, D0 will be the serial clock input: SCLK.
When I2C mode is selected, D2, D1 should be tied together and serve as SDA and D0 is the serial clock input, SCL.
14 D1
15 D2
16 D3
17 D4
18 D5
19 D6
20 D7
21 IREF I Current reference for brightness adjustment.
This is segment output current reference pin. A resistor should be connected between this pin and VSS .Set the current at 10 uA maximum.
22 VCOMH O COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS.
23 VCC P Power supply for OLED driving voltage. A capacitor should be connected between this pin and VSS.
24 NC(GND) P It should be connected to external ground.

Informazioni aggiuntive

P-Type

mode

Product No.

SCE154001-V01
Size

Resolution

outline dimension

Active Area

IC

Brightness

Touch Screen

View Direction

Pin No

Shape

interface

Prodotti correlati

Back To Top