OLED mono de 0.96 con 128x64, SSD1316BZ30PIN | Sinocrystal

OLED mono de 0.96 pulgadas con 128×64, SSD1316BZ IC, 30PIN, interfaz 6800/8080, interfaz serial de 4 cables, I2C

SCE096003-V01 es una pantalla OLED con tipo COG, resolución 128 × 64, SSD1306BZ IC, interfaz serie de 4 cables, 30PIN

Inquiry Now
SKU: SCE096003-V01
Type: OLED
Mode: -
Product No.: SCE096003-V01
Size: 0.96''
Resolution: 128*64
Outline Dimension: 26.70*19.26*1.41
Active Area: 21.744*10.864
Interface: 6800/8080 Interface/I2C/ 4-wire SPI
IC: SSD1306BZ
Brightness: -
Touch Screen: No
View Direction: -
Pin No.: 30
Shape: Rectangle

Descripción

                        Dibujo

 

 

 

 

                        Especificaciones generales

 

 

ITEM SPECIFICATIONS  UNIT
  MODULE SIZE 26.7(W)x19.26(H)x1.227(D) mm
  VIEWING AREA 23.74 (W) x 13.2(H) mm
  ACTIVE AREA 21.74(W) x11.2 (H) mm
  DOT SIZE 0.15(W) x0.15(H) mm
  DOT PITCH 0.17(W) x0.17 (H) mm
  ASSY.TYPE COG —
  WEIGHT TBD

 

 

                         Definición de interfaz

 

 

PIN NO. SYMBOL TYPE FUNCTION DESCRIPTIONS
1 NC(GND) P It should be connected to external ground.
2 C2P C1P/C1N-Pin for charge pump capacitor.
C2P/C2N-Pin for charge pump capacitor.
Connect to each other with a capacitor. They must be floated when the
Charge pump not use.
3 C2N
4 C1P I
5 C1N
6 VBAT P Power supply for charge pump regulator circuit.
It must be connected to external source when charge pump is used. It must be float when charge pump is not used.
7 NC NC
8 VSS P Ground pin. It must be connected to external ground.
9 VDD P Power pin for logic circuit. It must be connected to external source.
10 BS0 I Interface selection pins.

I2C 6800 8080 4SPI
BS0 0 0 0 0
BS1 1 0 1 0
BS2 0 1 1 0
11 BS1
12 BS2
13 CS# I Chip Select input pin. Active «L»
14 RES# I Hardware reset input pin. Active «L».
15 D/C# I This is Data/Command control pin.
When the pin is pulled HIGH, the data at D[7:0]  is data. When the pin is pulled LOW, the data at D[7:0] is command. In I2C mode, this pin acts as SA0 for slave address section.
When 3-wire serial interface is selected, this pin must be connected to VSS
16 R/W# I This is read/write control input pin.
8080: data write enable; 6800: read/write select pin.
When serial or I2C interface is selected, this pin must be connected to VSS.
17 E# I This is read/write control input pin.
8080: data read enable; 6800: read/write enable pin.
When serial or I2C interface is selected, this pin must be connected to VSS.
18 D0 I/O These are 8-bit bi-directional data bus to be connected to microprocessor’s Data bus.
When serial interface mode is selected, D2 should be kept NC, D1 will be the serial data input: SDIN, D0 will be the serial clock input: SCLK.
When I2C mode is selected, D2, D1 should be tied together and serve as SDA and D0 is the serial clock input, SCL.
19 D1
20 D2
21 D3
22 D4
23 D5
24 D6
25 D7
26 IREF I Current reference for brightness adjustment.
This is segment output current reference pin. A resistor should be connected between this pin and VSS .Set the current at 12.5 uA maximum.
27 VCOMH O COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS.
28 VCC P Power supply for OLED driving voltage. A capacitor should be connected between this pin and VSS, when charge pump is used.
It must be connected to external source when charge pump is not used.
29 VLSS P This is an analog ground pin. It should be connected to VSS externally.
30 NC(GND) P It should be connected to external ground.

Información adicional

P-Type

mode

Product No.

SCE096003-V01
Size

Resolution

outline dimension

Active Area

IC

Brightness

Touch Screen

View Direction

Pin No

Shape

interface

Productos relacionados

Volver arriba